5/71 Using the methods of this article, determine the sur- face area A and volume V of the body formed by re- volving the rectangular area through 360° about the Ans. A 10 300 mm², V- 24 700 mm³ z-axis. 12 mm 1 35 mm 8 mm

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: i cant read this.. can you write it out??

A:

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: 3.00- 1.25-

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: 5m %3D d=9·8\ mls? १त्र वह w Given data

A: Given data : The value of mass=m The value of acceleration due to gravity=g The value of height=h…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: 9. In a factory, packages are moved from a room on the second floor to a station on the first floor…

A: COEFFICIENT OF FRICTION DEPENDS ON MATERIAL

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: or columns should be the sum of when we place integers starting from 1 in a magic square of size…

A:

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the…

A: Weight of full spool = 2038=1638 ouncesEmpty Spool weight = 114 = 108 ounces

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: 1. show all steps in detail, units and formulas please.

A:

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: cm ỏ i 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft…

A: Smallest division of main scale =0.1 cm  Number of division in vernier scale =10  Least count =…

Q: name these lines

A: The names of the given lines is given below.

Q: why have you writen the answers in mm. when all the length are in meters

A:

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 5.5m x 6.2m x 7.7m x 4m x…

A: given; dimension of irregular shape of sheet metal;          (1m=39.3701inch)L1=5.5m=5.5*39.3701…

Q: . Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: According to the given details provided, we need to identify the view on the right that shows the…

Q: An exponent, such as the 4 in the expression 94, means: the number of times the number before the…

A: It is required to determine value of 94

Q: The Figure to the right shows a manufacturing process? What is this process called? 2. Identify the…

A: Given :-  1. What is the process called ?

Q: 7. What is a tolerance?

A: Measurement:  It is the numerical quantification of the body or event that is used to compare with…

Q: PLEASE WRITE LEGIBLY, COMPLETE SOLUTIONS WITH DRAWING THANK YOU! A car weighing 9 kN travels at 80…

A: Given:W=9 kNu=80 km/hrθ=10% incline

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.