51. Draw a feature control frame for a position tolerance. The tolerance zone is to be .024" diameterregardless of feature size. The tolerance is related to primary datum feature A, secondary datum featureC, and tertiary datum feature F. (Note that the datum feature references are not A, B, C.)52. Complete a feature control frame for a position tolerance. The tolerance zone is to be .031" diameter when thefeature is at maximum material condition. The tolerance is related to primary datum feature D, secondarydatum feature C, and tertiary datum feature G. (Note that the datum feature references are not A, B, C.)

Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Answered: 51. Draw a feature control frame for a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need these 3 parts answered TRUE or FALSE.
Provide the appropriate datum feature symbols and datum features in the feature control frames on the drawing
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. Please refer to the attached image.
I need help answering this quick review pertaining to the print provided.
1. All orientation controls must have maximum material condition O a large tolerance zone O red text O datum features ?
1. How is the location tolerance of Position different from the other 11 GD&T tolerances? Pick two (2) other tolerance and contrast write about those two in detail relative to Position tolerancing. 2. Form tolerances, elaborate how they are different from Orientation tolerances
There is a position tolerance applied to a four hole pattern and another position tolerance to a single hole. Calculate the diameter of a pinused as the secondary datum feature B simulator for these position tolerance.
Need Help on both Questions.
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
Skectch a tool that properly locates the datum reference frame. Show possible points of contact that would stablize the part in the tool and meet the order of precedence for the referenced datums. (show at least three points on primary datum feature)

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS