5. Name a testing method performed to check standard tightness of tower bolts. 6. This is a document laminated and installed at the ACPDB door cabinet to check electrical loading, 7. What are the number of days after pouring should the concrete reach its required 70% and 100% compressive strength and tested by third party testing center? 7th and 14th day 7th and 21th day 7th and 28th day 14th and 28th day 8. This is a testing method performed to check overall straightness of the tower. 9. What is the maximum value for earth or grounding resistance test? 10. What do you call device/tool used for measuring the galvanization or coating of grounding and tower materials?

5. Name a testing method performed to check standard tightness of tower bolts. 6. This is a document laminated and installed at the ACPDB door cabinet to check electrical loading, 7. What are the number of days after pouring should the concrete reach its required 70% and 100% compressive strength and tested by third party testing center? 7th and 14th day 7th and 21th day 7th and 28th day 14th and 28th day 8. This is a testing method performed to check overall straightness of the tower. 9. What is the maximum value for earth or grounding resistance test? 10. What do you call device/tool used for measuring the galvanization or coating of grounding and tower materials?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: Discuss positive aspects of bleeding in concrete.
Concrete technology
In order to evaluate the sustainability of non-potable water available in the job site for mixing concrete, six standard mortar cubes were made using that water and six others using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the loads to failure (in kN) shown in table below. Based on these results, would you accept that water for mixing concrete? Cubes made with Cubes made with non-potable water potable water 64.6 73.5 70.4 74.8 63.0 79.7 71.6 69.8 70.6 83.7 64.0 74.4
You are a trainee at the building site which had 3000 NFP bricks delivered. You then determined the compressive strength of each bricks as per SANS227 testing regulations. Bricks were ordered with a nominal compressive strength of 3,5 MPa and minimum individual value of 3,0 Mpa. The results from the lab are as follows: Compressive strength Sample 2 3,4 3,7 Sample 1 3,4 Sample 3 3,4 3,7 Brick no 1 3,7 3 3,5 3,5 3,5 3,2 3,7 3,2 3,3 4 3,2 5 3,7 4,1 3,6 4,0 7 3,9 3,4 3,9 8 3,1 3,1 3,1 3,3 3,3 3,3 2,9 3,1 3,6 3,4 10 3,9 11 4,1 3,8 12 3,7 3,7 From the above set of results, state whether these bricks would be accepted or rejected for based on their strength. Support your answers.
In order to evaluate the suitability of nonpotable water available at the job site for mixing concrete, six standard mortar cubes were made using that water and six others using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the loads to failure (in kN) shown in Table P6.21. a. Based on these results only, would you accept that water for mixing concrete according to ASTM C94? b. According to ASTM C94, are there other tests to be performed to evaluate the suitability of that water? Discuss briefly. TABLE P6.21 Cubes Made with Cubes Made with Potable Water Nonpotable Water 64.6 73.5 70.4 74.8 63.0 79.7 71.6 69.8 70.6 83.7 64.0 74.4
Hand written solution is not allowed bro.
Problem 6: Find a real-world reinforced concrete failure. Was it a strength or service limit state failure? Discuss what happened and why it happened, and if design codes were changed so the same thing would not happen again.
.
4. Suggest, with justification, a method of preventing/delaying each of the following causes of damage in concrete. i) Frost damage ii) Thermal cracking in a large mass of concrete iii) Plastic shrinkage
Problem 1: Calculate Mn and check the minimum steel limit f'c =4 ksi, fy 60 ksi. 2.5" 25" 6-#9 12" 3.5" 4" 25"
ASAAPP!! A fence has a dimension of 15 meters long and 20 meters high including the portion below NGL. how many bags of cement will be needed for the cement mortar using class A mix. CHB used is 200x200x400mm
Why Consistency test of cement is performed?