5. I copied the following out of the Arduino programming guide. Finish filling in the table showing me how toreplace the following function calls to pinMode and digitalWrite with simple C code and assembly code.Make sure you calculate the appropriate masks.PORTD maps to Arduino digital pins 0 to 7DDRD The Port D Data Direction Register - read/write (IO Address 0x0A, Memory Address 0x002A)PORTD The Port D Data Register - read/write (10 Address 0x0B, Memory Address 0x002B)(library functions) C-Code (using & and(memory mapped IO)pinMode(4,OUTPUT);masks)(legacy IO assembly)asm volatile("sbi 0x0A, 4 \n\t");//method 4, memory mapped ioasm volatile ("lds r24, 0x002A \n\t""ori r24, 0x10 \n\t"sts 0x002A, r24 \n\t"digitalWrite(4,HIGH);PORTD PORTD | 0x10digitalWrite(4,LOW);asm volatile("cbi 0x0B, 4 \n\t");//method 4, memory mapped ioasm volatile(lds r24, 0x002B \n\t""andi r24, 0xEF \n\t"*sts 0x0028, r24 \n\t";

The objective of the question is to replace the Arduino library functions with equivalent C code and…

Answered: 5. I copied the following out of the…

Similar questions

This is a block diagram of a microprocessor. Inta Rst 6.5 Trap Rst 7.5 Intr Rst 5.5 SID SOD Interrupt control Serial I/O control 8-bit internal data bus Accumulator Instruction decoder (8) Temp reg. (8) Flag (5) flip flops B C. Reg (8) (8) Instruction Reg Arithmetic decoder D (8) (8) and Reg Reg logic unit L (8) (8) Reg Register array machine Reg (ALU) (8) cycle encoding Stack pointer (16) Program counter (16) +5 V GND Power supply Incrementer/ decrementer address latch (16) Timing and control Reset CIk Gen Control Status DMA Address buffer (8) Data/address buffer (8) RD WR ALE S, S, IO/M Hold Clk out Hlda Reset out Ready Reset in A1s-Ag To Address bus AD-AD To Address/data bus
5. I copied the following out of the Arduino programming guide. Finish filling in the table showing me how to replace the following function calls to pinMode and digitalWrite with simple C code and assembly code. Make sure you calculate the appropriate masks. PORTD maps to Arduino digital pins 0 to 7 DDRD The Port D Data Direction Register - read/write (IO Address 0x0A, Memory Address 0x002A) PORTD The Port D Data Register - read/write (10 Address 0x0B, Memory Address 0x002B) (library functions) C-Code (using & and (memory mapped IO) pinMode(4, OUTPUT); masks) (legacy IO assembly) asm volatile( "sbi 0x0A, 4 \n\t" ); //method 4, memory mapped io asm volatile ( "lds r24, 0x002A \n\t" "ori r24, 0x10 \n\t "sts 0x002A, r24 \n\t" digitalWrite(4, HIGH); PORTD PORTD | 0x10 digitalWrite(4, LOW); asm volatile( "cbi 0x0B, 4 \n\t" ); //method 4, memory mapped io asm volatile( lds r24, 0x002B \n\t" "andi r24, 0xEF \n\t" *sts 0x0028, r24 \n\t ";
Develop the assembly code for the following: Load 10 Hex values in 10 memory location. Next find the sum of all the values loaded in the memory location. At the end Register A should contain low byte and Register R5 High byte of the final result.
3. Compile the following high-level code into RISC-V pseudo assembly language. Assume variable a and val are stored in memory as words. Make sure you load these values into registers before you use them and store back any changes to memory. You can use "Iw x5, a" and "sw x5, a" as pseudoinstructions for load and store a word for variable a, considering a is a symbol for the address of the memory that store the value of a. This question is for you to practice using shift-logic instruction, logic (AND, OR, etc) instructions as well as branch instructions. If (a e 30) ( val - (val & exFF00)- 20; else ( val - (val » 12) - 5;