5. A tank has two identical orifices in one of its vertical sides. The upper orifice is 3 m below the water surface and the lower one is 7 m below the water surface. If the coefficient of velocity is 0.95, find the point of intersection of the two jets. 6. A closed tank partially filled with water up to a height of 2 m, having an orifice of diameter 10 mm at the bottom of the tank. Determine the pressure required for a discharge of 2.5 L/s through the orifice. Coefficient of discharge is 0.67. 7. The water is flowing through a pipe of diameter 150 mm. The pipe is inclined and a venturimeter is inserted in the pipe. The diameter of the venture meter at the throat is 75 mm. The difference of pressure between the inlet and the throat is measured by a liquid of specific gravity 0.85 in an inverted U-tube which gives a reading of 250 mm. The loss of head between the inlet and throat is 03 times the kinetic head of the nine Find the discharge

5. A tank has two identical orifices in one of its vertical sides. The upper orifice is 3 m below the water surface and the lower one is 7 m below the water surface. If the coefficient of velocity is 0.95, find the point of intersection of the two jets. 6. A closed tank partially filled with water up to a height of 2 m, having an orifice of diameter 10 mm at the bottom of the tank. Determine the pressure required for a discharge of 2.5 L/s through the orifice. Coefficient of discharge is 0.67. 7. The water is flowing through a pipe of diameter 150 mm. The pipe is inclined and a venturimeter is inserted in the pipe. The diameter of the venture meter at the throat is 75 mm. The difference of pressure between the inlet and the throat is measured by a liquid of specific gravity 0.85 in an inverted U-tube which gives a reading of 250 mm. The loss of head between the inlet and throat is 03 times the kinetic head of the nine Find the discharge

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bernoulli's theorem demonstration: 5 L of Water is flowing through a venturimeter in 6.5s. What is the pressure difference (p1- P2) (in kPa) for this flow? D=32 mm, d=23 mm, g = 9.8 m/s² and y=9.8 kN/m³
simple answer is enough
4. A cylindrical tank is having a hemispherical base. The height of cylindrical portion is 5 m and diameter is 4 m. At the bottom of this tank an orifice of diameter 200 mm is fitted. Find the time (in minutes) required to completely emptying the tank. Take C=0.6 (20 pts) 5 m II 4.0 m 2.0 m ORIFICE
Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a is 6 m/s and 300000 Pa respectively.a.) what is the speed of fluid at point b?b.) what is the pressure at point b which is higher than point a for about 5cm?
A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v, the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m %3D
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
A vertical circular tank that is 1,5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameters respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0,8 m long, 0,5 m below it's vertex. If the tank is originally full of water, what time is required to empty the tank? Take discharge coefficient as 0,63.
What is the velocity t the summit
In a pump that works with cold water, the discharge pressure gauge located 7.5 m above the axis of the pump marks a pressure height of 68 m.c.a. The vacuum gauge located 125 cm below the axis of the pump shows a relative pressure of 325 Torr. Due to the difference in diameters between the suction pipes The momentum is created a dynamic height of ½ m. Calculate the useful head of the pump?
An orifice having an area of 0.0003 m2 is located on the vertical side of a tank. The tank has a constant cross-sectional area of 0.40 m2. It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Determine the following:a. Coefficient of dischargeb. The time to lower the head from 1.20 m to 0.80 m when C = 0.60.c. The head after 240 seconds from an initial head of 1.20 m when C = 0.60