If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter of the tank is 20m then is the tank filling or emptying? At what rate is the water level rising or falling in the tank? 20 m dia water V= 0.6 m/s V =0.5mis. 30 cm dia 35 cm dia Q = 0.00569 m3/s O Lowering @ 0.018 mm/s No change of water level. O Rising @ 0.018 mm/s

If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter of the tank is 20m then is the tank filling or emptying? At what rate is the water level rising or falling in the tank? 20 m dia water V= 0.6 m/s V =0.5mis. 30 cm dia 35 cm dia Q = 0.00569 m3/s O Lowering @ 0.018 mm/s No change of water level. O Rising @ 0.018 mm/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

L = 900m D=35cm L=600m L=900m D=75cm D=60cm L=600m D=30cm L=900m D=40cm A flow rate of 0.5 m³/s is branched into three pipes and then rejoined in the concrete parallel pipes as shown in the figure below. Find the head of loss between point A and point B. Here, the coefficient of friction loss in all tubes is 0.03.
A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v, the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m %3D
Draw hp, hes and h, for the system shown in figure (A). Flow V Soil T K=1.5 cm/sec 2 Soil Il K=0.5 cm/sec Figure (A) DIL 1.0 m 1.5 m 1.0 m 1.0 m 1
Fast
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
- once answered correctly will UPVOTE!!