2. A closed vertical cylindrical vessel, 1.50m in diameter, 3m high is 8/10 full of liquid (SG=1.03) and is revolved about its vertical axis with a 15 rad/s speed. The air inside the vessel is 58 kPa. a. Determine the maximum pressure on the tank. b. What is the diameter of the portion free of liquid at the bottom of the tank?

2. A closed vertical cylindrical vessel, 1.50m in diameter, 3m high is 8/10 full of liquid (SG=1.03) and is revolved about its vertical axis with a 15 rad/s speed. The air inside the vessel is 58 kPa. a. Determine the maximum pressure on the tank. b. What is the diameter of the portion free of liquid at the bottom of the tank?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a is 6 m/s and 300000 Pa respectively.a.) what is the speed of fluid at point b?b.) what is the pressure at point b which is higher than point a for about 5cm?
2. Oil of specific gravity of 0.90 is discharging through a 100 mm circular sharp edge orifice in the end of a 120mm pipe. The pressure head on the center line of the pipe just upstream from the orifice is 9m of oil, and discharges takes place into a closed tank in which the vapor pressure is - 20 kPa. Use C = 0.68 and Cv = 0.97. Compute the discharge. 120 mm pipe P = - 20 kPa 100 mm orifice
The velocity potential for a certain inviscid flow field is -(7xy-y) where o has the units of ft2/s when xand y are in teet. Determine the pressure difference (in psi) between the points (1, 2) and (8, 8), where the coordinates are in feet. if the fluid is water and elevation changes are negligible. P1 P2= psi
solution only
5-9 A 0.75-m³ rigid tank initially contains air whose den- sity is 1.18 kg/m³. The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m³. Determine the mass of air that has entered the tank. 2.83
3-160 A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is open to the atmosphere through a vent in the middle. The tank is now accelerated to the right on a level surface at 2 m/s2. Determine the maxi- mum pressure in the tank relative to the atmospheric pressure. Answer: 29.5 kPa 1.5 m 2.5 m Vent Water tank FIGURE P3-160 5 m 2 m/s2
Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 97.1 kPa. The gage pressure at section (1) is 103 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 103 kPa, V₁ = 4 m/s. (a) Kx = i 2260.24 (b) to the left N V₂ 160 mm Section (2) 300 mm V₁ Water Section (1) P1 V₁
Homework 14 |A cylindrical vessel closed at the top and bo om is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its ver cal axis, nd the pressure head at the bo om of the vessel at the center point and at the edge.
A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (y = 50.0 lbf/ft3), 5 ft of water, and 2 ft of mercury (y = 846 lbf/ft3). Compute (a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right-hand side of the tank.