5. A rectangular aluminum block is 90 mm long in the X-direction, 70 mm wide in the Y-direction, and 40 mm thick in the Z-direction. The block is subjected to axial loads of 220 kN tensile force in the X direction, 150 kN compressive force in the Y direction, and 200 kN tensile force in the Z-direction. Assume that v = 0.33 and E = 70 GPa. Determine the single load in the X-direction that would produce the same Z deformation as the original loading.

5. A rectangular aluminum block is 90 mm long in the X-direction, 70 mm wide in the Y-direction, and 40 mm thick in the Z-direction. The block is subjected to axial loads of 220 kN tensile force in the X direction, 150 kN compressive force in the Y direction, and 200 kN tensile force in the Z-direction. Assume that v = 0.33 and E = 70 GPa. Determine the single load in the X-direction that would produce the same Z deformation as the original loading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm THICK IN THE Z DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF 210 KN (COMPRESSION), 170 KN (TENSION) AND 230 KN (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON'S RATIO = 1/4 & E= 72 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETERMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME Z DEFORMATION AS THE ORIGINAL.
Situation 4. A cast iron link is 50mm wide by 250mm high by 550 mm long. The allowable stressin tension is 50 MPa and 85 MPa in compression. Assume that load P (tensile axialload) is placed at 30 mm distance from the neutral axis. A. What is the value of tensile normal stress in MPa? B. What is the value of bending stress in MPa? C. What is the value of the combined stress?
SITUATION I. For Items 3-5. Refer to figure 1. Axial loads are applied at rod FIGURE 1 a composed of bronze rigidly attached together. If P = 3000 lb and the cross-sectional steel, aluminum, and 4P Steel Bronze area of the rod is 0.5 in?, in the Aluminum 3. Determine the stress bronze. 2 ft a. 6000 psi b. 12000 psi c. 18000 psi d. 24000 psi 3 ft 2.5 ft е. none of the above
11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are circular fillets of in. radius on each side. If the bar is subjected to an axial tensile load of 12,000 lb, calculate (a) the average tensile stress in the wide portion of the bar some distance from the change in section. (b) the average tensile stress in the narrow part of the bar. (c) the maximum tensile stress adjacent to the circular wild fillet. 11 10 A long flat steel bar 5 in wide and in thick has a circu 162111 3 H ar 11.28 A P (a (E
Homework 8: A (20°C) a rigid beam in placed upon the rods shown in figure: 1) Determine the magnitude of uniformly distributed load w (kN/m) so that beam remains horizontal when temperature of steel becomes to (100°C). 2) Find the stress developed in each rod. Steel A, = 1000mm², as = 12 * 10-6 , E, = 200GPA, L = 500mm %3D %3D Aluminum Aal 1500mm2, aal = 23 * 10-6 , Eal = 70GPA, L = 300mm %3| Rigid beam w (kN /m) A C steel Aluminum 3m 3m
Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.