5. A circular plate made up of steel sg= 7.85 is submerged in a fluid of sg-1.029. If the force acting on one side of the plate is 69lb and the upper tip of the plate from the fluid surface is unknown, determine the diameter of the circular plate in ft and the location of force from the fluid surface in ft. Eccentricity is 0.04.

5. A circular plate made up of steel sg= 7.85 is submerged in a fluid of sg-1.029. If the force acting on one side of the plate is 69lb and the upper tip of the plate from the fluid surface is unknown, determine the diameter of the circular plate in ft and the location of force from the fluid surface in ft. Eccentricity is 0.04.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Panel AB is circular and retains a liquid with specific gravity of 1.55. It has a width of 4 feet perpendicular to the paper. It has a radius of 13 feet from its center as seen in the figure. If h = 6 feet, and a = 2 feet, determine the total hydrostatic force acting on panel AB in pounds.
A horizontal nozzle of 30 mm diameter discharges a steady jet of water into the atmosphere at a rate of 15 litre per second. The diameter of inlet to the nozzle is 100 mm. The jet impinges normal to a flat stationary plate held close to the nozzle end. Neglecting air friction and considering the density of water as 1000 kg/m³, the force exerted by the jet (in N) on the plate is -
A trapezoidal plate shown in the figure is submerged in water is 2.4 m below the surface. The bases of the plate is 3 m and 6 m, respectively. The height is 11 m. Find the hydrostatic force acting on the plate in Newton. Unit weight of water is 9.75 KN/m³. Answer is in KN. Write only the value of your answer. FES b ^
Fluid
Which could be the applied force in Newtons of a moving plate (area 0.1m2) and (v=2m/s) in between two different fluids: %3D over the plate: 3mm of Fluid 1 with viscosity of 0.001 Pa-s under the plate: 4mm of Fluid 2 with viscosity of 0.002 Pa-s O 0.18 O 0.17 O 0.19 O 0.15 O 0.16 O 0.20
Problem 5 In the figure shown, what is the static pressure in kPa in the air chamber? AIR 2.0 m OIL 4.0 m S=0.80 5.0 m WATER 3.0 m
H =2m Seawater y = 0.2x2 y 25 m The concrete seawall given in Figure 4 has a curved surface and restrains seawater at a depth of 2 m. The trace of the surface is a parabola as illustrated. Determine the force of the fluid force (per unit length) with respect to an axis through the toe (point A). 1024kg/m³) (Y seawater = -X
A 3 m square plate is immersed vertically in water such that the two edges of the square are horizontal. The center of pressure is located 8 cm from the centroid of the square plate. Calculate the distance in m of the center of pressure from the water surface.
2. In figure below fluid 1 is oil (SG=0.87) and fluid 2 is glycerin (SG=1.26) at 20°C. If P₁ = 98kPa, determine the absolute pressure at point A. Gu 10 cm P₂ Pa 32 cm Figure 2. Schematic for problem 2
Choose the best answer among the following choices stated in each problem. Your choice must be supported with complete solution
I need the answer as soon as possible
5. The 1.5m diameter solid cylinder shown is 7m long perpendicular to the figure and rests in static equilibrium against a frictionless wall at 0. Determine the unit weight of the cylinder. oil sg = 0.82