4m 4m 2m C 2m & 2m A 500 kg nonuniform boom, 6.0 m long, is loosely pinned at the pivot at P. A 400 kg block is suspended from the end of the boom at A. The boom forms a 30° angle with the horizontal, and is supported by a cable, 4.0 m long, between points D and B. Point B is 4.0 m from P, and point D is 4.0 m above P. The center of mass of the boom is at point C, which is 2.0 m from P. In the figure, the y-component of the pivot force on the boom at P is closest to: O 7800 N 4700 N O 1x10 N O 1.3x10 N 5600 N Submit Request Answer

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.

A: 13.A full section results when the cutting plane is completely passed through a part feature.Hence,…

Q: While performing a visual inspection you measure a mill-induced discontinuity to be 1 1/2" long and…

A: Visual Inspection, used in maintenance of facilities, mean inspection of equipment and structures…

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: How did you determine to round up to 55 mm if the table never mention anything about 55 mm?

A: H=55 mm

Q: The frame shown could be subjected to a variety of loads applied at different points. Consider the…

A:

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: If a sample of iron is cut in half, do the two pieces have the same density as the original sample?…

A: Here, density is defined as mass per unit Volume. and density is intensive property. Intensive…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: what happened with the 10 in the first equation?

A:

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: I need answers for problems 10, 11, and 12 pertaining to the print provided.

A: 10.In general, the reference dimension is used for information purpose only. It doesn’t have any…

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Q: What is the moment's function?

A: Moment deals with the physical quantities situated at some distance relative to the reference point.…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.