4-9 Determine the force required to punch a slug hav-ing the shape shown in Figure P4-9 from a sheetof aluminum 3003-H18 having a thickness of0.194 in. 0.60 in.1.60 in.0.40 in.0.80 in.E P4-9 Shape of a slug for Problem 4-9.

Answered: 4-9 Determine the force required to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
Q: Figure (1) shows a schematic drawing of a countershaft which is part of the conveyor system and supports two belt pulleys (A & B). The belt tensions are parallel for pulley B and inclincd with angle 45° for pulley A. The pulley A reccives a power from a motor and then delivers to conveyor belt through pulley B. All dimensions are in mm. Required: Design the shaft as shown in figure (1) at points O, A, B & E. Pulley B Material Discharge Material Fead Pulley A Conveyor System -Tail Pulley Gear box- Sepport Belt Motor Drive balt 300 310.5 N 400 46.5 N 150 Figure (1) 250 dia.- 300 dia. 50 N Pulley A Pulley B 270 N Page 1 of 1
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
Problems 5-111 through 5-116 Figures P5-111 through P5-116 show completed shearing force diagrams for beams. Develop the loading diagram and the bending moment diagram for each beam.
solve, show all steps for given solution.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

4-9 Determine the force required to punch a slug hav- ing the shape shown in Figure P4-9 from a sheet of aluminum 3003-H18 having a thickness of 0.194 in. 0.60 in. 1.60 in. 0.40 in. 0.80 in. E P4-9 Shape of a slug for Problem 4-9.