40 mm 12 mm 40 mm 30 mm 10 mm 50 mm 10 mm 30 mm

Q: 30 mm 600 mm 36 mm T = 500 N-m с 900 mm 5 Two solid steel shafts are fitted with flanges that are…

A: The rotation of the flange with respect to other flange is φb=1.5°=0.02618 rad. The applied torque…

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod. Knowing that both…

A: we are going to apply the Torsion equation over the shaft.

Q: L/4 w L/2 L/A B A timber beam AB of length L and rectangular cross section carries a uniformly…

A:

Q: 3. A torque T is applied to two tubes with the cross-sections shown. Assuming the same shear stress…

A: To find: The ratio of shear flow. Given: The inner diameter of the tube is d1=a-t. The outer…

Q: 2. Link AB, of width b 5 50 mm and thickness t 5 6 mm, is used to support the end of a horizontal…

A: Given:  I think the values given are not correct so i have taken appropriate values to solve this…

Q: Link AB, of width b =50 mm and thickness t = 6 mm, is used to support the end of a horizontal beam.…

A: Given Width = 50 mm Thickness = 6 mm Allowable normal stress = 2140 MPa Allowable shear shear stress…

Q: The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with ry= 22…

A:

Q: Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces.…

A: Wooden Member

Q: The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with Ty= 22…

A: The torque applied is T=73 kip.in The length of the rod AB is L=35 ft. The radius of rod AB is r=1.2…

Q: PROBLEM 8.40 A thin strap is wrapped around a solid rod of radius c = 20 mm as shown. Knowing that I…

A:

Q: Link AB, of width b = 2 in. and thicknesst = ¼ in., is used to support the end of a horizontal beam.…

A: Handwriting.jpg

Q: Knowing thát the internal diameter of the HolUW SIlat shown is d= 23 mm, determine the maximum shear…

A:

Q: Load P is applied to a steel rod supported as shown by an aluminum plate into which a…

A:

Q: Link AB, of width b = 50 mm and thickness,t = 6 mm, is used to support the end of a horizontal beam.…

A: Given data: b=50 mmt=6 mmσ=2140 MPaτ=80 MPa Need to determine the diameter of the pins and average…

Q: Problem 4 The steel pipe AB has a 102-mam outer diameter and a 6-mm wall thickness. Knowing that arm…

A:

Q: The built-up wooden beam shown is subjected to a vertical shear of 8 kN. Knowing that the nails are…

A: Given data The spacing of nails at A, sA =60 mm. The spacing of nails at B, sB = 25 mm. Moment of…

Q: PROBLEM 3.11 Knowing that each portion of the shaft AD consists of a solid circular rod, determine…

A:

Q: T C. | I I Η Κ 10 kN 240 mm

A:

Q: For the element shown, determine the range of values of τxy for which the maximum in-plane shearing…

A: Given data: Maximum shear stress, τmax = 150 MPa. Stress in the x-direction, σx = -20 MPa. Stress…

Q: For the state of stress shown, determine the maximum shearing stress when (a) ơ, = 0, (b) ơz = 60…

A: σavg=1230+100 =6512σx-σy=1230-100=-35

Q: For the state of plane stress shown, determine the maximum shearing stress when (a) o, = 14 ksi and…

A:

Q: 50 mm 100 mm 50 mm 150 mm 50 mm Three boards, each 50 mm thick, are nailed together to form a beam…

A: