The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with Ty= 22 si and G=11.2 × 106 psi. Knowing that a torque T=73 kip-in. is applied to the rod and then emoved, determine the maximum residual shearing stress in the rod. 35 ft أول -1.2 in. The maximum residual shearing stress in the rod is ksi.

Q: Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the…

A: Shear stress of magnesium = 45 MPaShear stress of steel = 75 MPaModulus of rigidity magnesium = 18 ×…

Q: P C B D T 150 mm 150 mm

A:

Q: Determine the value of Q so that the deformation at A is zero.

A: Given:E = 70 GPaP = 3.5 kNDiagram is givenTo find:Value of Q so that the deformation at A is zero

Q: PROBLEM 3.56 Two solid steel shafts are fitted with flanges which are then connected by fitted bolts…

A: ** Make BC as CD

Q: Using Tall = 8.7 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled yellow…

A:

Q: E' 3. For the 3-in.-diameter solid cylinder and loading shown, T = 40 kip-in., determine: (a) the…

A:

Q: The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with ry= 22…

A:

Q: The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing…

A: Given Data: The diameter of the rod AB is: dAB= 60 mm The outer diameter of the pipe CD is: dCD=90…

Q: Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that Birass…

A: For solution refer below images.

Q: The driveshaft of an automobile is being designed to transmit 172 hp at 2950 rpm. Determine the…

A:

Q: 5 mm 20 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 5 mm 20 mm .5 mm 250 mm

A:

Q: 3. A shaft composed of segments AC, CD and DB is fastened to rigid walls and loaded as shown. For…

A: Solution:(a) Free Body Diagram (FBD) of the Composite ShaftFirst, let's understand the torques at…

Q: Load P is applied to a steel rod supported as shown by an aluminum plate into which a…

A:

Q: The solid circular shaft shown is made of a steel that is assumed to be elastoplastic with ry= 145…

A: The below information is given: τY = 145 MPa = 145 × 106 Pa c = 32 mm = 0.032 m Plastic zone tp =…

Q: 3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a…

A: Given Data Modulus of rigidity is : G=77 GPa Length section of BC is : LBC=0.8 m Length section of…

Q: please see attached screenshot

A: Step 1:Angle of twist at A, ϕA = 6.02o

Q: d₁ = 38 mm d₂

A:

Q: The solid circular shaft shown is made of a steel that is assumed to be elastoplastic with Ty= 145…

A: The answer is provided below

Q: The two shaft

A: Design of shaft is important process in any mechanical system. Design of shaft is determined by…

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: 7o solid steel shafts are connected to f a disk B. Knowing the modulus of = d the allowable shear…

A: given:shear stress τ=90MPa

Q: The torque T causes a rotation of 2° at end B of the stainless-steel bar shown. Knowing that b = 20…

A: The rotation of the bar is .The distances are given as-The length of the bar is .The shear modulus…

Q: 3. The stepped shaft shown is supported by bearings at A and B. Determine the maximum stress in the…

A: Given Data r=3 mm

Q: An 18-mm-diameter solid circular shaft is made of a material that is assumed to be elastoplastic…

A: According to the data provided in the question. D=18mm G=77.2Gpa L=1.2m T=207N.m We need to find The…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.