40 D 2a В 4a 2а 4а 390 The columns AC and DE are connected to the bars BD and CD by pins. The support at A is a pin and the support at E is a roller. Determine the forces acting on each column due to the horizontal linearly distributed load on AC and vertical unifrom load on CD. Present your solution as two FBDS showing the actual forces.

40 D 2a В 4a 2а 4а 390 The columns AC and DE are connected to the bars BD and CD by pins. The support at A is a pin and the support at E is a roller. Determine the forces acting on each column due to the horizontal linearly distributed load on AC and vertical unifrom load on CD. Present your solution as two FBDS showing the actual forces.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.
|%A• In. ? Asst. Prof. Muhammed Abbas المعلم منذ ۱۲ ساعات مضت. H.W.2: Find the 40 k force in each G member of the 5 k truss. 16 ft V17 F 10 k 10 k 16 ft 3 B - 8 ft- 8 ft- 4 ft 4 ft 4 ft 4 ft 4.
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
DETERMINE THE THE IS MAXIMUM SAFE SERVICE LIVE LOAD THAT THE BEAM CAN CAN CARRY IF SERVICE DEAD L O A D THE BEAM WEIGHT OF THE BEAM SECTION fy = 415 MPa. TOP BARS BOTTOM BARS ARE CENTER DISTANCE 12 KM/M INCLUDING AND BASED ON THE CAPACITY SHOWN. fc : 40 MPa AND ARE 6-32 mm. AND ARE - 3 - 28 mm. CENTER TO 3 BETWEEN THE USE 2015 NSCP Is 108 mm 00 0 0 300 G ט1 108 352 70. A (1 7.2m B TOP BAR LAYERS ↓ 6.7M C OM
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
Please answer properly. a.) Identify the zero-force members (Draw the system without them) b.) Through the method of joints, identify the forces acting on N and Q
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)
Note:hand written solution should ne avoided.
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
Present your solution and box your final answer
Which of the following statements is correct about the given structure? A В D E r pin fixed roller fixed It is a determinate structure. It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. It is indeterminate to 3 degrees.