4. The normal stress on plane pq of a prismatic bar in tension (see figure)is found to be 7500 psi. On plane rs, which makes an angle 6=30º withplane pq, the stress is found to be 2500 psi. Determine the maximumnormal stress ơmax and maximum shear stress Tmax in the bar.300→P

Answered: Image /qna-images/answer/7408c385-f600-42ed-935d-3e92cbe45163.jpg

4. The normal stress on plane pq of a prismatic bar in tension (see figure) is found to be 7500 psi. On plane rs, which makes an angle 6=30° with plane pq, the stress is found to be 2500 psi. Determine the maximum normal stress Omax and maximum shear stress Tmax in the bar. 300 →P

4. The normal stress on plane pq of a prismatic bar in tension (see figure) is found to be 7500 psi. On plane rs, which makes an angle 6=30° with plane pq, the stress is found to be 2500 psi. Determine the maximum normal stress Omax and maximum shear stress Tmax in the bar. 300 →P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The plate below is attached to the vertical surface AB. Its top and bottom surfaces slide smoothly along the horizontal surfaces AD and BC, but are prevented from moving vertically. The plate can move freely in the z- direction (perpendicular to the page). The right side of the plate is uniformly pulled such that it displaces 0.8 mm to the right. The plate is aluminum, which has the following material properties: 150 nim BERA Modulus of Elasticity = 88.5 GPa %3D 150 num F0.8mm Modulus of Rigidity 34 GPa %3D Poisson Ratio = 0.32
A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force P (in kips rounded to the nearest tenths) required to punch the slot. Assume d = 0.75 in. and a = 4.00 in.
The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube (2) has an allowable shear stress of 8 ksi. The outside diameter of the tube is D2 = 1.63 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B.Calculate(a) the largest torque T that can be applied at the upper end of the steel rod if the allowable shear stress in tube (2) is not to be exceeded.(b) the corresponding minimum diameter d1 required for steel rod (1).
Solve it fast.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 11 ksi, and Sxy = 17 ksi. (a) Draw Mohr’s circle for this state of stress. (b) Determine the principal stresses (σp1>σp2) and the maximum in-plane shear stress τmax acting at the point. (c) Find the smallest rotation angle θp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
The solid circular rod has a cross-sectional area of 470mm². It is subjected to a uniform axial distributed loading along its length of w= 11kN/m. Two concentrated loads also act on the rod: P = 4 kN and Q=2 kN. Determine the normal stress in the rod at x = 1.0 m. Assume a = 0.5 m and b = 1.4 m. a Answer: σ= i B W MPa
3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T = 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for %3D %3D %3D bronze, and G = 75 GPa for steel. %3D 75 mm 50 mm A Bronze Steel C T a -
The split ring shown has an inner radius ₁ = 0.8 in. and a circular cross section of diameter d= 0.6 in. Knowing that each of the 100-lb forces Pis applied at the centroid of the cross section, determine the stress at point A and at point B. P B The stress at point A is The stress at point B is P ksi. ksi.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 27 ksi, S, = 16 ksi, and Sxy = 14 ksi. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (opl > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) S Answers: Opl = i ksi. Op2 = i ksi. Tmax = ksi. i
In a triaxial stress system, the six components of the stress at a point are: 0x = 6 MPa Try = 1 MPa σyy = 5 MPa Ty₂ = 3 MPa σ = 4 MPa T₁ = 2 MPa Determine the normal and shearing stress on the plane whose direction cosines are 1/3, 1/3, 1/√√3. Also calculate the direction of the shear stress.
The state of stress at a point is shown on the element. Enter your answers numerically separated by commas. ΥΠ ΑΣφ vec max min = ksi Submit Request Answer Figure Part B Determine the absolute maximum shear stress. ΑΣφ ve 2.5 ksi ksi Fabs mar= 4 ksi Submit Request Answer 5 ksi Provide Feedback 圓

The state of stress at a point with ox, oy, and txy as shown. Analyze the state of stress at the point using the Mohr's circle of stress. Determine the following a) Principal stress, b) Maximum in-plane shear stress and c) Normal stress on the plane defined by x' axis where the angle is 25 degrees. Ne To 0. ox x TEV