Problem (4.4): The aluminum-alloy shaft AC in Figure (4.25) (G= 26 GPa) has an 800-mm-long solid segment AB and a 400-mm-long tubular segment BC. The shaft issubjected to the torsional loading shown in the figure. The diameters are di=(d.)2 = 50mm and (d;)2 = 20 mm.(a) Determine the maximum shear stress in the shaft, and identify the location (s) wherethis maximum shear stress occurs.(b) Determine the angle of rotation at B. Øg. and the angle of rotation at C. Øc.8 kN-m800 mmCp)B3 kN-m400 mm(di)2

Answered: Image /qna-images/answer/3a5b350d-75cb-4e0e-8d10-533f8b92718c.jpg

Problem (4.4): The aluminum-alloy shaft AC in Figure (4.25) (G= 26 GPa) has an 800- mm-long solid segment AB and a 400-mm-long tubular segment BC. The shaft is subjected to the torsional loading shown in the figure. The diameters are di-(d.)2 = 50 mm and (d)2 = 20 mm. %3D (a) Determine the maximum shear stress in the shaft, and identify the location (s) where this maximum shear stress occurs. (b) Determine the angle of rotation at B. ØB. and the angle of rotation at C. Oc. A (1) (d2 8 kN-m 800 mm B (2) 3 kN-m 400 mm (d)2

Problem (4.4): The aluminum-alloy shaft AC in Figure (4.25) (G= 26 GPa) has an 800- mm-long solid segment AB and a 400-mm-long tubular segment BC. The shaft is subjected to the torsional loading shown in the figure. The diameters are di-(d.)2 = 50 mm and (d)2 = 20 mm. %3D (a) Determine the maximum shear stress in the shaft, and identify the location (s) where this maximum shear stress occurs. (b) Determine the angle of rotation at B. ØB. and the angle of rotation at C. Oc. A (1) (d2 8 kN-m 800 mm B (2) 3 kN-m 400 mm (d)2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve quick
Principal stress: 01,2 Ox+0y tan20, = Txy 2 (Ox-0y)/2 2 maximum in-plane shear stress: Tmax *) : + Txy? tan20s -(0x-0y)/2 Ox+0y σανg Txy 2 The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Show your work. 57 MPa 28 MPa 42 MPa
A thin-walled circular tube and a solid circularbar of the same material (see figure) are subjectedto torsion. The tube and bar have the samecross-sectional area and the same length.What is the ratio of the strain energy U1 in the tubeto the strain energy U2 in the solid bar if the maximumshear stresses are the same in both cases? (For thetube, use the approximate theory for thin-walled bars.)
A rigid bar ABCD is supported by two bars as shown in Figure below. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (1) is 590 µ. Determine: a. The normal strain in bar (2). b. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin C before the load is applied. c. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin B before the load is applied. (2) 1,500 mm 240 mm 465mm 140 mm Rigid bar B C 900 mm (1) P.
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
3. For the given state of stress, determine the principal planes, the principal stresses, the max shear stress. You must use Mohr's Circle. 20 MPa 32 MPa 55 MPa
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
thanks
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
Consider the state of plane stress shown. (Hint: Consider both in-plane and out-of-plane shearing stresses.) 7 ksi Determine the maximum shearing stress when ox- 18 ksi and ay = 8 ksl. The maximum shearing stress is ksi.
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?