4. In a natural gas pipe line compressor, 110 m³/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38°C. The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW.

4. In a natural gas pipe line compressor, 110 m³/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38°C. The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and cp = 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ = 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. = = State 2 Isentropic Compressor State 1 Air-perfect gas T₁ = 300K P₁= 1 bar Answer: W tubine = ? State 4 Isentropic Turbine State 3 Steam T3=320°C P3= 2MPa What is the mass flow rate of steam through the turbine? Please enter your answer in kg/s
Q4: A diffuser, has air entering at 100 kPa, 280 K, with a velocity of 200 m/s. The inlet cross-sectional area of the diffuser is 100 mm2. At the exit, the area is 860 mm2, and the exit velocity is 20 m/s. Determine the exit pressure and temperature of the air. Take Cp=1.005 KJ/kg.K OA: 280 K OB: 300 K OC: 320 K D: 340 K
Steam expands from 9.0 MPa and 4500C to saturated vapor @75 kPa through an adiabatic turbine. If the mass flow rate is 20 kg/s, how much power will be generated (in MW)? 22.7 B) 25.3 11.9 D 7.95
3. Nitrogen gas @ 90° F (MW=28) goes through a compressor, increasing its pressure from 10 psi to 65 psi. The temperature remained constant throughout. Determine the work in Hp for a steady flow process; AKE=0, APE=0; mass flow rate of nitrogen is 2 Ibm/min.
Steam enters the nozzle operating a steady state pressure of 2.5 MPa and a temperature of 300 °C ( H1 = 3008.8 kJ/kg) and leaves at a pressure of 1.7 MPa with a velocity of 470 m/s. The rate of flow of steam through the nozzle is 1360 kg/hr. Neglecting the inlet velocity of the steam and considering the flow in the nozzle is adiabatic, find:a. the exit enthalpy in kJ/kg, ( H2)b. the nozzle exit area ( in cm) if V exit is 0.132 m^3 /kg c. the system
13. During a reversible process, 2.09 kg/s of gas rejects 322.9 kJ/s of heat isothermally at 25.5°C. For this gas, cp = 2.14 kJ/kg K and c, 1.62 kJ/kg K. The initial pressure is 551.7 kPa. Determine the work steady flow of the process in hp if APE = 2.8 kJ/s and AKE = 6.2 kJ/s.
In a natural gas pipeline compressor, 110 m3/min. propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 0 The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature, (b) the mass flow rate, (c) the heat loss, and (d) the work required.
An air enters a compressor at 120 kPa, 20 C with volume flow rate of 10m^3/min. It then exits the compressor at 1.5Mpa and 145 C. Calculate the power input to drive the compressor (under steady state) when heat transfer from the compressor is 2 kW.
A power plant operates in an idealized Rankine cycle, using water as the working fluid (Figure 3). The steam at the exit of the boiler has a pressure of 6 MPa and temperature of 600 °C (point 1). The water at the exit of the condenser has a pressure of 15 kPa (point 3). The condenser employs a nearby river as the cooling source, which can be regarded to have a constant temperature of 25 °C. The mass flow rate of the steam is 80 kg/s. The hot reservoir has a temperature of 1400 K. Regard water as an incompressible liquid. During pumping, the density of water remains unchanged as Point 3 in Figure 3. Qin Boiler i wwwwww Pump Turbine Wp 3 Figure 3 W₁ Cooling water Condenser
2. A steady stream of steam passes through a turbine. The steam inlet conditions are 10MPa, 450°C and 80m/s and at the outlet they are 10kPa, 92% quality and 50m/s. The mass flow of the steam is 12 kg/s. Determine a) the change in kinetic energy, b) the power developed by the turbine, and c) the area of the turbine inlet.
A reciprocating air compressor takes in air at 1 bar, 25 deg. C, and compresses it to a pressure of 5 bar running at 300 rpm. The compression follows the PV1.3=C. The clearance is 4% of stroke volume and mass flow rate of air 0.1 kg/s. Determine the power input to the compressor, and volumetric efficiency. Represent the process on p-v and T-s planes. Assume for air R=287 J/kg.K