4. For two-point loading bending test of a beam shown in Fig. 3, the maximum moment was found (100+R) kN-m. If the Modulus of elasticity of the beam is 200,000 MPa, calculate the value of applied load P in kN, maximum deflection in mm and maximum bending stress in MPa. P (KN) P (KN) ↓ 1.5m 4 2m 1.5 m Fig. 3 300 mm 380 mm

Q: how J1 is 4 please count it on the graph with explain. (And when do we count the link and the j1…

A: Consider the instantaneous diagram of the mechanism as shown below. The unknown dimensions in the…

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: In this calculus proble, a machine design has endpoints of a moveable rod of length 1 meter have…

A:

Q: Give all the location dimensions between the datum target points, B1 ,C1 and B2, C1. B1, C1 : X =…

A: Since, the bottom part of the drawing represents dimensions in X and Y direction while the upper…

Q: The state of an object varies over time, but at any particular points it is determined by:   Which…

A: The state of an object varies over time, then it must be dependent upon the state of the object…

Q: Translate the following set of equations into the index notation by using the rule of the free…

A:

Q: Need a sectional view of this drawing

A: Given DataThe length of the object is 110.00 units.The width of the object is 54.00 units.The height…

Q: For the 3-DOF Industrial manipulator arm as shown in Figure 3, determine the joint displacements for…

A:

Q: For an undamped vibratory system, the velocity leads the displacement by rt/2 rad. Select one: O…

A: False

Q: 4. Using the data of table 2, fill the table below. To calculate the "calculated range" Ax, use the…

A: Data for measured and calculated values are, Delta(X) measured Delta(X) calcualted 1.937…

Q: C 4) The Wire C The Wire BC X C 4) The Wire x C The Wire BC X The Wire BC x C 4) The Wire x G 3.)…

A: To Find : The mass of the heaviest possible uniform cylinder supported. Given :  The Initial…

Q: (xo, Yo) Ay = Number (x,y) m 00 Given the above graph plotting y position against a position, where…

A: xo = 0 myo = -4 mx = 5 my= 0 m

Q: Quarterback Quick Release can throw a football in a perfect parabolic arc to a receiver 40 yards…

A: A body is launched with a velocity that forms an angle with the horizontal in projectile motion,…

Q: Questions 5 through 8 refer to the situation depicted below. Power la delivered by a motor (not…

A: The tight side or slag side of  of the pulley is  dependent on the  direction of the of the power…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.