4. Design a collector-coupled monostable multivibrator shown in Fig. 2(a) to obtain an output pulse of amplitude 10 V. Given that Ic(sat)= 10 mA, IB2 = 21B2 (min), VCE(sat) = 0.1 V, VBE(sat) = 0.3 V, hFE(min) = 40 and a pulse of duration 1000 μs is required. VBE(cut-off). Voc Rc www ww Rc R₁ www Q₁ OFF 182 ΩΣ ΟΝ Saturation -VBB Fig.2 A collector-coupled monostable multivibrator

4. Design a collector-coupled monostable multivibrator shown in Fig. 2(a) to obtain an output pulse of amplitude 10 V. Given that Ic(sat)= 10 mA, IB2 = 21B2 (min), VCE(sat) = 0.1 V, VBE(sat) = 0.3 V, hFE(min) = 40 and a pulse of duration 1000 μs is required. VBE(cut-off). Voc Rc www ww Rc R₁ www Q₁ OFF 182 ΩΣ ΟΝ Saturation -VBB Fig.2 A collector-coupled monostable multivibrator

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. If you have this relationship between the input and output voltage Vou=1.5 Vin+2 in which 2 is a bias. Design a circuit that will remove the bias and make the relationship between the input and output as Vou=1.5 Vin. We have a dual supply of ± 12 V available and we need to drive a 10 kQ load. Test your designs under different input voltages and verify that your output voltages are within + 5% of the calculated ones. Simulate the circuit in Multisim and then implement it practically. Prepare a full report about the experiment.
slove 5 (Use a BJT op-amp) 1 You’ve been asked to build an alarm system using monstable multvibrator having an active time pf 100msec.. Explain the principle of operation and the type feedback of the op-amp. What is the advantage of this circuit? 2 You’ve been asked to build a low frequency square wave generator using a basic comparator having a frequency of 10kHz and 50% duty cycle. Explain the principle of operation and the type of feedback of the op-amp. What is the advantage of this circuit? 3 3 Build a Wein-Bridge oscillator using, C=1µF and +10V power supply to produce 10 kHz sinusoidal waveform. Generate your plots and compare output results. Highlight any discrepancies and discuss what happens if we want to increase the frequency to 100 kHz. 4 Build a high frequency Colpitts oscillator producing 10kHz Discuss its advantage over RC oscillators. How can you modify the circuit to include a crystal in you circuit. What is a typical application of such an oscillator? 5 Discuss the…
Q.4) a- The LM317 is used as a voltage regulator: i- Draw the standard external connection to get this function. ii- drive an expression for output voltage as a function of the external resistances used in (i). iii- select the values of resistors to be used in circuit(i) that is required to produce an output for the external voltage of 12V with an input of 18V. the maximum regulator current with no load is to be 2mA. There is no external pass transistor, assume I adjusted is 50µA.
EleetroniC Analysis and s Introduction to Electronic Analysis and Design - CE255/EE255 - O1 -Spring Common Source MOSFET Amplifier has Select one: a. input is connected to the Source and the output is taken from the Drain b. input is connected to the Gate and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Source d. input is connected to the Source and the output is taken from the Gate 255 week 10 material Jump to... 16 CE255/EE255 (01)-
A transistor output noise voltage is measured at 15microvolts when the standardized noise source is at the input. With the noise source removed, a noise voltage of 5 microvolts is measured. Calculate the noise figure.
7. When the automatic gain control voltage of a radio receiver is measured with a vacuum tube voltmeter whose input resistance is 10 M-ohm, it reads 4.5 V. When an ordinary voltmeter whose input resistance is 10 k-ohm is also connected across the AGC voltage source, both meters read 0.40. What is the internal resistance of the AGC voltage source? 8. A phonograph pick up develops an open-circuit emf of 50 mV and has an internal resistance of 1200 ohm. A. What voltage will it develop across a 4 ohms load resistance? B. What value of load resistance must be used to obtain a 75% eff? C. What is the maximum power output of the pickup? 9. What bleeder resistor is required to complete a voltage divider to give 300 v at 40 mA from a 500 V source of emf if the series dropping resistor is 4 k-ohm.
24 3 Vsige VGG I RO RS VAP Vout Rout Consider the mosFET Circuit Shown In which &p=3-3 kuz Ac and Rs=4702. The Dc Sources VOD and VGG Set gm = 15 MATU Determine the Overall Voltage gan, Cav Determine the 2 Determine the F3 Out Put resistance Input resistance
A 3 ph F.W. 1/2 controlled converter with highly inductive load ,R=10, V=400 RMS and Out=15A.Find alpha.
Find the desired in point 54 with finding what you can find.
2. 3. 5. Using the data when the gate voltage is 0, explain how you could use your JFET as a two-terminal current source that gives a current of Ipss. (a) Does the experimental data indicate that the transconductance is a constant at all points? (b) From your experimental data, what evidence indicates that a JFET is a nonlinear device? Why should a JFET be operated with only reverse bias on the gate source?
5
Please Solve this Question: Design a Relaxation oscillator (using 1 OPAMP, 3 resistors and 1 capacitor) togenerate a square waveform of period 220us and 50% duty cycle.