b) 1) Design (Find R₁, R2, and R3) a voltage-controlled-oscillator (VCO) that has the output change frequency Af. = 40kHz. Assume Vcc = 15V, VCN = 10V, C₁ = 1nF, R₂ = 0.5R₁ (Do not assume the value of R₁)and if VCN is varied by ±12%. 2) Draw the design circuit and output waveform. 3) Determine fo. 4) Verify the value of Af, by using a voltage-to-frequency transfer coefficient (K). 5) Verify the value of VCN= 10V.

b) 1) Design (Find R₁, R2, and R3) a voltage-controlled-oscillator (VCO) that has the output change frequency Af. = 40kHz. Assume Vcc = 15V, VCN = 10V, C₁ = 1nF, R₂ = 0.5R₁ (Do not assume the value of R₁)and if VCN is varied by ±12%. 2) Draw the design circuit and output waveform. 3) Determine fo. 4) Verify the value of Af, by using a voltage-to-frequency transfer coefficient (K). 5) Verify the value of VCN= 10V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A3 A Thermister has 6500oc resistance at 20oC, and its sensitivity is -7.2%/oC. Design a signalconditioning set-up for an out of 4V, at 21.5oC-with and without self-heating. Let Vs = 10V, and PD=of 4.1mW/oC.
Answer the following with illustration and solutions. 2.) If C1 = C2 = 100pF, determine the output frequencies produced by this arrangement:a. (a) when R1 = R2 = 12kilo-ohms andb. (b) when R1 = R2 = 8kilo-ohms See the example below..
Q.4) a- The LM317 is used as a voltage regulator: i- Draw the standard external connection to get this function. ii- drive an expression for output voltage as a function of the external resistances used in (i). iii- select the values of resistors to be used in circuit(i) that is required to produce an output for the external voltage of 12V with an input of 18V. the maximum regulator current with no load is to be 2mA. There is no external pass transistor, assume I adjusted is 50µA.
A transistor output noise voltage is measured at 15microvolts when the standardized noise source is at the input. With the noise source removed, a noise voltage of 5 microvolts is measured. Calculate the noise figure.
H3
Only part 4and5
help me please..................
A 3 ph F.W. 1/2 controlled converter with highly inductive load ,R=10, V=400 RMS and Out=15A.Find alpha.
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
3. For the following circuit assumer, = 33.4 N a. Draw the small signal equivalent circuit. b. Find the input impedance. c. Find output impedance. d. Find the voltage gain. -10 V 68 k2 4.7 kA e. Find the current gain. a = 0.998 10 uS
In a Wien bridge oscillator circuit, the value of the resistor andnthe capacitor that form the RC series and parallel branch are given as 200 ohm and 10 mF. What will be the frequency of oscillation?
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.