)a- The LM317 is used as a voltáge regulator: i- Draw the standard external connection to get this function. ii- drive an expression for output voltage as a function of the external resistances used in (i) ii- select the values of resistors to be used in circuit(i) that is required to produce an output the external voltage of 12V with an input of 18V. the maximum regulator current with no is to be 2mA. There is no external pass transistor, assume I adjusted is 50µA.

)a- The LM317 is used as a voltáge regulator: i- Draw the standard external connection to get this function. ii- drive an expression for output voltage as a function of the external resistances used in (i) ii- select the values of resistors to be used in circuit(i) that is required to produce an output the external voltage of 12V with an input of 18V. the maximum regulator current with no is to be 2mA. There is no external pass transistor, assume I adjusted is 50µA.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
3. For the half-wave rectifier given in the figure below, find the average values of the output voltage and current, and the ripple factor of the output voltage. D1 Io Dbreak R1 1k vo VAMPL = 169.71 FREQ = 50
To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the assigned voltages to each of the bins. b- Determine the voltage that will be assigned to a measurement reading -3.25 V. Calculate the percentage ADC error. c- Determine the voltage that will be assigned to a measurement reading 4.11 V. Calculate the percentage ADC error.
2) approximately draw Vout for the circuits below, separately. Point out which one is a rectifier which one is a clipping circuit. Use Vp = 0.7V. Input signal 2tVin 1.5 1 0.5 -0.5 -1 -1.5 -2 Circuit (a) Circuit (b) Vin Vout Vin Vaut R 2 Vonut 1.5 1.5 1 1 0.5 0.5 1 3 4 7 1 2 3 6 7 -0.5 -0.5 -1 -1 -1.5 -1.5 -2, -2
Draw the output voltage waveform of the circuit shown. Make sure to label the values.
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
. Design a half wave rectifier using an op-amp. The output voltage should be -10V(peak) and the input voltage shouldbe 50Vac(peak) (1kHz, 0°).
Design a full wave rectifier based on the circuit shown in Figure 5 below: N: N2 D3 RL ww US D, Figure 5 The required specification for the full wave rectifier circuit includes the peak output voltage of 5 V, deliver 100 mA to the load R1, and produce an output with a ripple of not more than 5 percent. An input line voltage of 220 V (ms), 50 Hz is available. Given V, =0.7 V. (d) Calculate v, (max). (e) Find the required turn ratio for the transformer. (1) Determine the Peak Inverse Voltage (PIV). (g) What is the effective load resistance? (h) Determine the required capacitance of the filter capacitor.
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 162 V and the firing angle of the SCR is 60 degrees, the peak voltage of the input sinusoidal would be: O A. 197 V O B. 228 V O C. Can't tell; need more information. O D. 340 V O E. None of the other choices are correct
The figure below shows the input waveforms for a NOR latch. Draw the corresponding output waveforms. S A Q
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Question 3 The 555 timer is connected in the following circuit. The resistance of the extra resistor is 102, the capacitance of the extra capacitor is 0.1F. The voltage input at Pin2 is Vcc. What is the output state at Pin3? 1) 2) Decide the voltage input value at Pin 6 when the condition is stable. 3) Decide the output state at Pin3 when a trigger input is applied at Pin2 (voltage input at Pin2 changes from Vcc to 0, and return back to Vcc immediately). 4) After the trigger input is applied at Pin2, how long would the output maintain at the unstable state. Vc R O Output Vo 555 Vc 0.01µF Trigger Input