In the clamping circuit shown below and made with an ideal diode, as C1 = C2 = 200 nF given. The frequency of the input shown below is between 5kHz and 20kHz and is Vi signal with an amplitude value of 20 V was applied. For all frequency values of the input signal in the circuit As it is desired to be taken from the exit by clamping at the desired level without distortion; ww www www a) What should be the smallest value that the R resistor to use can get? b) Draw the output waveform for the case under a and show the amplitude values on the figure. (the initial transient state is negligible). www +10 V ideal Vi R Vo

In the clamping circuit shown below and made with an ideal diode, as C1 = C2 = 200 nF given. The frequency of the input shown below is between 5kHz and 20kHz and is Vi signal with an amplitude value of 20 V was applied. For all frequency values of the input signal in the circuit As it is desired to be taken from the exit by clamping at the desired level without distortion; ww www www a) What should be the smallest value that the R resistor to use can get? b) Draw the output waveform for the case under a and show the amplitude values on the figure. (the initial transient state is negligible). www +10 V ideal Vi R Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please provide a COMPLETE and CLEAR solution.
Do the diagram in ltspice app.
G2/.Design Circint as the following peseripton: A- the positive Cycle of the vout signal is 3.2 and Negative cycle is 4-33 (Note: we must used preetical Diodes and vin is lov) 13- the positive cyclep of vout is s.3 ond Negative cycle is (5.4) [Note:consider vin = tovavd we must used Capaetor with praeticul Didde)
Explain the importance of the Volt-Ampere Characteristics of P-N Diode
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
Sketch the I-V characteristic curve for a real diode and label the main parameters and regions.
Assuming that the diodes in the circuits shown below are ideal, find the values of the labeled voltages and currents.
use a P-N junction ideal diode to simulate a circuit measure and plot its I-V characteristics as well as its forward characteristics. assume breakdown voltage of around 6V for your calculations. I have added my multisim design with IV graph of the diode. I need : the large signal piece wise linear parameters of the diode. and for the plot do the theoretical calculations for at least one point on the curve and mark it on the curve This peoblem has other part that I will send when the expert answered this part. Tnx
(2) In the adjacent circuit, the input signal Vin = F15V is a square wave. Draw the output signal as a function of time on both Vin ends of: (a)- load resistance. (b) Di-zener Vz=6V In terms of behavior, the value of the output voltage is fixed on the drawing, bearing in mind that the diode is made of
R VD 3cos(1000nt) VOUT 0.7 V What are the minimum and maximum values of Vout assuming the offset model for a diode with Von = 0,7 V for the input signal shown below? Chọn một: O a. Minimum -3 V, maximum 1.4 V O b. Minimum 1.4 V, maximum 3 V O c. Minimum 0.7 V, maximum 3 V O d. Minimum -3 V maximum 0.7 V O e. Minimum -3 V, maximum 3 V
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
Question 4