Circuit 2: Clamper Circuit OSC1 +Ch2 0.1F Vo HH 4vpp'1Htz d. Set the input signal of the clamper circuit to 4Vp-p and 1 kHz square wave, shown circuit above. Show the input and the output waveform. e. Reverse the connection of a diode in Circuit 2 and plot the input and the output waveform. Determine the Vp-p of the input and output voltages. 1n4001

Circuit 2: Clamper Circuit OSC1 +Ch2 0.1F Vo HH 4vpp'1Htz d. Set the input signal of the clamper circuit to 4Vp-p and 1 kHz square wave, shown circuit above. Show the input and the output waveform. e. Reverse the connection of a diode in Circuit 2 and plot the input and the output waveform. Determine the Vp-p of the input and output voltages. 1n4001

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Please can you help with question B
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.
Considering a clamper circuit, where capacitance C, load R, the cut-in voltage of diode are unknown, which is the correct statement 1- the dc level of the signal changes 2- the peak-to-peak value of signal changes 3- the shape of signal changes 4- the dc level shifts up 5- the dc level shifts down
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi