4. A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between the pressure tape along the pipe is 1.5 m, the differential pressure is 70kPa, and the water temperature is 70°C, what is the discharge of water in m³/sec?. Assume coefficient of 0.985.

4. A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between the pressure tape along the pipe is 1.5 m, the differential pressure is 70kPa, and the water temperature is 70°C, what is the discharge of water in m³/sec?. Assume coefficient of 0.985.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plugged dishwasher sink with the dimensions of 16 in. ✕ 19 in. ✕ 5 in. is being filled with water from a faucet with an inner diameter of 1 in. It takes 250 seconds to fill the sink to its rim. Imagine the plug of the sink leaks. If it now takes 290 seconds to fill the sink to its rim, estimate the mass-flow rate of the leak (in lbm/s).
I want full solution, this is one question only if u can't solve them all handwritten then I suggest u to skip, I'll upvote
A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward direction. A differential mercury manometer connected to inlet and throat gives reading of 200 mm. Find discharge through pipe. Take Ca%3D.0.98.
Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady, incompressible, irrational with negligible frictional effects , the effect of air column on the pressure change is negligible, the pressure can be assumed to be uniform at a given cross-section of the venturi meter and the flow is horizontal . Air is flowing through a venturi meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, take the air density to be 0.075 lbm/ft. 1. Show that the volume flow rate can be expressed as: 2(P P2) | = A, p(1 – AŽIA}) 2. Find the flow rate of the air? 12.2 psia 11.8 psia Air 2.6 in 1.8 in
A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of 50 m than the ground. The discharge at the end of the pipe is 220 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 35 N/cm². Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id....) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m) ,
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 110 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.9 and sp. gr of oil = 0.9 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) = Question 8 个
Water is flowing downward in a pipe in the figure shown at 0.02 cu. m. per sec. having diameters of 8 cm. and 4 cm. respectively. Determine the values of pressures (a) at pt. 2, P2 and (b) at pt. 1, P1 if the pressure at pt. 1 is twice as great as the pressure at pt. 2. H20 8 ст. Ф 1.5 m 2 datum 4 cm. Đ
A venturi meter has water flowing through it. The pressure difference is 1 psi. The diameter at point 1 is 1 ft, and that at point 2 is 0.5 ft. What is the volumetric flow rate through this meter?A. 0.03 m³/sB. 0.04 m³/sC. 0.06 m³/sD. 0.07 m³/s
Problem 5: A fluid flows by gravity down an 8-cm galvanized ironpipe. The pressures at the higher and lower locations are 120 kPaand 140 kPa, respectively. The horizontal distance between thetwo locations is 30 m, and the pipe has a slope of 1-m rise per10 m of run (horizontal distance). For a fluid with a kinematicviscosity of 10-6 m2/s and a density of 900 kg/m3, determinethe flow rate (in m3/s).
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
I need the answer as soon as possible
Find the loss of head when pipe of diameter 30 cm is suddenly enlarged to a diameter of 40 cm. The rate of flow of water through the pipe is 300 lit/sec.