HWIWater is flowing through a pipe having diameter of 300 mm and 200 mm at thebottom and upper end respectively. The pressure at the bottom end is 24.525x 10N'm and the pressture at the upper end is 9.81x 10* Nm. Detennine the difference indatum head (Z, - Z,), if the rate of volume flow through the pipe is 40 L's. (Assumeideal flow)D, 200 mmP981 Niem0, 300 mmP, 24 525 NiemDATUM LINE

Name: HWIWater is flowing through a pipe having diameter of 300 mm and 200
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: HWIWater is flowing through a pipe having diameter of 300 mm and 200 mm at thebottom and upper end respectively. The pressure at the bottom end is 24.525x 10N'm and the pressture at the upper end is 9.81x 10* Nm. Detennine the difference indatum hea

Answered: Image /qna-images/answer/9018a85b-963f-4072-9062-eccd5e7e81a7.jpg

Engineering

Mechanical Engineering

HWI Water is flowing through a pipe having diameter of 300 mm and 200 mm at the bottom and upper end respectively. The pressure at the bottom end is 24.525x 10 N'm and the pressure at the upper end is 9.81x 10 Nm. Deternine the difference in datum head (2,- Z,), if the rate of volune flow through the pipe is 40 Ls (Assume ideal flow) D, 200 mm 0, 300 mm P24525 Niem DATUM LINE

HWI Water is flowing through a pipe having diameter of 300 mm and 200 mm at the bottom and upper end respectively. The pressure at the bottom end is 24.525x 10 N'm and the pressure at the upper end is 9.81x 10 Nm. Deternine the difference in datum head (2,- Z,), if the rate of volune flow through the pipe is 40 Ls (Assume ideal flow) D, 200 mm 0, 300 mm P24525 Niem DATUM LINE

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the flow Q and the velocity V when total head loss is H = 25 m?
Ex5:- From Figure shown, the pipe line have Qa = 15L/s, QB = 3QD, DA=100 mm, DB= Dc = 25mm, Dp= 50 mm and vc = 4m/s. Find the value of discharge and velocities for pipes A, B, C and D? %3D
I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The then breaks into N narrow Pipes (which have a diameter, d2, and a length, L2), before the water is released to the atmosphere, as shown in the figure. The entrance to the small pipe from the large pipe has a loss coefficient of KL. You may assume the flow is laminar and fully developed everywhere in the system, and that any changes in height are neglible. (The viscosity is NOT negligible) a) Find an expressin for the velocity of water leaving the sprinkler b) Find an Expression for the gauge pressure at point A, a distance L1 upstream of the narrow pipes. Express your answer in terms of the flowrate, Q. c) The inner diameter of the first segment of the pipe is d1 = 10mm, the inner diameter of the second set of pipes is d2 = 1mm, with N = 25. The flowrate through the sprinkler is Q = 0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds…
Water flows thiough a horizontal pipe at o veiociy of 50 ft per secon d. Owing to the pipe gradually expanding to larger rize, the velocity decreases to 35 f1 per second, what i the differentce between the prewures at two points, one in each size of pipe ? Given : VA =(50fps Ve -35 fps 1,421.88 psf 1,165.15 psf O 1,345.11 psf 1,021.96 psf 1,236.75 psf
Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe characteristics are as follows: (Take the flow rate equals 0.6m³/sec) and (u = 10-6 m²/sec). %3D Pipe 1 L(m) 900 D(mm) 600 e or for CH.w. e 0.25mm 300 f 0.03 f = 0.02 CHW. 130 2 1500 3 1000 400 4 1500 750 Flow A
The air is measured at 20 deg. C and 533mm Hg. The duct diameter is 622 mm while the discharge diameter is 385mm The fan draws 2 m^3/s air and the static pressure measured is 8 cm water Determine the power output in kW ndmal places
solveeee very very fast in 15 min | I need a clear answer by hand, not by keyboard
I am having trouble with this problem.
please help me with this exercise ...
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
I need the answer as soon as possible
4