4 units of 2716 EEPROM ( 2^10 X 8) is to be connected to an X brand Microprocessor which has 16 bit Address Bus. Show and design how we can connect this 4 2716 EEPROM. What is the total storage ? Show addresses for each of the 2716 chip.

4 units of 2716 EEPROM ( 2^10 X 8) is to be connected to an X brand Microprocessor which has 16 bit Address Bus. Show and design how we can connect this 4 2716 EEPROM. What is the total storage ? Show addresses for each of the 2716 chip.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Related questions

Q: Assume r1=0x02 in 8 bit representation, what ARM assembly instruction will you use to perform the…

A: To perform multiplication in ARM assembly, we can use the MUL instruction. To multiply r1 with 4, we…

Q: will TMR0 need to be incremented before it overflows? 72. How many instructions cycles will that…

A: According to the question, for the continuing with a 32 KHz system clock/8000 KHz instruction…

Q: interface four chips of 128k×8 SRAM to 8086 microprocessor using separate bank write strobes such…

Q: How we can achieve double Precision 64-bit computation using MIPS environment, while MIPS only…

Q: Consider the following situation: In an 8088-based microprocessor, it is needed to interface with 6…

A: We are going to design microprocessor which is 8088 based. The 8255 was widely used in many…

Q: Question 4 Why must the single-cycle datapath have separate instruction and data memories? The…

A: answer is

Q: I need someone to explain me step by step ( in a simple way) how does this microcontroller works or…

A: High performance PIC12F508/509 the device can be attributed to a number of architectural functions…

Concept explainers

Properties of different architectures

Software architectures are the blueprint of a software system. They consist of all components involved in a system, relations between various components, the environment of operation, and the principle used in designing the software. In other words, software architecture shows the organization of different software structures and helps understand their behavior.

Question

Transcribed Image Text:4 units of 2716 EEPROM ( 2^10 X 8 ) is to be connected to an X brand Microprocessor which has 16 bit Address Bus. Show and design how we can connect this 4 2716 EEPROM. What is the total storage ? Show addresses for each of the 2716 chip.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful, do not copy and paste off chatgpt
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful
Using four 32 x 8 ROM chips, design a circuit such that the effective size of the ROM circuit is 64 x 16. The ROM chip must show the Address inputs, enable input, and data connections. As shown in the lessons, use the MSB(s) of the combined address lines as the chip selection lines.
How we can achieve double Precision 64-bit computation using MIPS environment, while MIPS only offers 32-bit registers? Note:- (Please give detailed answers to the above ask question.)
The number of address bits that are needed to uniquely identify all memory location in 8Gi x 16 chip is bits.
Answer ii)
Design a 16-bit common bus system using tri-state buffers and other devices you may need. The sources of data are three 16-bit registers (A, B, and C) and two 8-bit registers (D and E). Draw all the connections and show all the details.
Given the following memory chip configurations find the requested information: An EPROM chip has a capacity of 128Kbits with 8 bits of information stored at each location, what is the organization of the chip? how many address pins and data pins does the chip require? A DRAM chip has a capacity of 16Mbits and with 4 bits of information stored at each location, what is the organization of the chip? how many address pins and data pins does the chip require? For the ROM memory chip shown, find the capacity (including units): organization: is this memory volatile or non-volatile? (circle one) D7 DO A B YO A16 A17 A0 Y1 A18 Y2 b ROM G2A G2B Y3 Y4 Y5 o Y6 o Y7 o A15 A19 G1 VccVpp MEMR OE Given the ROM memory chip and decoder circuit below (the decoder used is the 74LS138) is used in a system with a 20-bit address bus, find the address range (in hex) the chip will respond to: upper CE Each Y controls one block lower
Please finish fast but accurate.Thank you!
Question 4 Why must the single-cycle datapath have separate instruction and data memories? The formats of data and instructions are different in RISC-V, and hence different memories are needed. It is less expensive to have separate memories. The processor operates in one cycle and cannot use a (single-ported) memory for two different accesses within that cycle. All of the above.
A digital computer has a common bus system for 16 registers of 32 -bits each. The bus is constructed with the use of multiplixers. Answer the following questions. a) How many multiplixers are needed to design this common bus? Explain your answer.
interface four chips of 128k×8 SRAM to 8086 microprocessor using separate bank write strobes such that the upper and the lower banks each contains two chips. Identify the address range of the memory