Question 4 Why must the single-cycle datapath have separate instruction and data memories? The formats of data and instructions are different in RISC-V, and hence different memories are needed. It is less expensive to have separate memories. O The processor operates in one cycle and cannot use a (single-ported) memory for two different accesses within that cycle. All of the above.

Question 4 Why must the single-cycle datapath have separate instruction and data memories? The formats of data and instructions are different in RISC-V, and hence different memories are needed. It is less expensive to have separate memories. O The processor operates in one cycle and cannot use a (single-ported) memory for two different accesses within that cycle. All of the above.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: What is the main issue of a single data path design? Need multiple Multiplexors.…

A: Answer: The main issue of single data path design is long cycle time. Hence, “Longest delay…

Q: We have two 4-bit registers A, B available, each with the standard “Load" input. When "Load" is at…

A: To design the data path for this case, we need to use a combination of logic gates and multiplexers.…

Q: The CLC ISA ( a pretend ISA) is under development and in a state of flux. The CLC ISA uses a 40 bit…

A: Maximum number of instructions possible with n bits is given by 2n Hence maximum number of…

Q: An omega switching network connects 4096 RISC CPUS, each with a 60-nsec cycle time, to 4096…

Q: 3. Given the data 0×123456789ABC and the starting location (lowest address) of data memory (0x018)…

A: GIVEN:

Q: for (i=0; i<=w; i++) for (j=0; j<y; j+=2) A[3*i + j] = 2*i +3*j;

A: X4=w, X5=y, X6=i, X7=j add X6, X0, X0 // i=0 Loop1: beg X6, X4, DONE // go to DONE if i=w…

Q: Assume the following sequence of instructions is executed on a five-stage pipelined datapath: add…

A: Instructions in a pipelined datapath are separated into stages to allow for parallel execution,…

Q: Assume that a RISC processor executes each instruction in 2 microseconds and that an I/O device can…

A: When I/O devices are not yet prepared to supply data or handle the request, the interrupts are a way…

Q: Suppose we have the instruction Load 1200. Given memory as follows: Memory 1000 1100 1200 800…

A: Please upvote, I am providing you the correct answer below. Please please. 1. Indirect…

Q: For the following RISC-V assembly instructions below, what is a single corresponding C statement?…

A: In computеr programming, assеmbly languagе is a low-lеvеl programming languagе that is closеly…

Q: Registers in RISC-V are 64-bit. For the sake of simplicity, consider the following instructions…

A: RISC-V which is an open standard instruction set architecture that are based on established RISC…

Q: What would occur if an instruction were to be disregarded? A software-managed TLB is speedier than a…

A: Ignoring an instruction can lead to various consequences, depending on the instruction Being…

Q: The hypothetical machine of Figure 3.4 also has two I/O instructions: In these cases, the 12-bit…

Q: An 8-bit data is read from an input device and stored in the memory location 0x20000200. This data…

A: Assembly instructions: MOV This instruction copies the source operand value to destination register.…

Q: Problem 5: Suppose the program counter (PC) is set to 0x60000000hex. a. What range of addresses…

A: in jal instruction, the immediate field has 20 bits.This field only references addressesthat are…

Q: Given von Neumann architecture, name three (3) special purpose registers in CPU? Explain and discuss…

A: Actually, register is a used to stores the data/information.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Assume an I/O device may only wait for an interrupt to be handled for up to 1 millisecond, and that a RISC processor executes each instruction in 2 microseconds. There is a hard limit on the number of instructions that may be executed with interruptions deactivated.
Assume an I/O device may only wait for an interrupt to be handled for up to 1 millisecond, and that a RISC processor executes each instruction in 2 microseconds. There is a hard limit on the number of instructions that may be executed with interruptions deactivated.
The 8051 memory map is subdivided into separate program/code and data memory.Describe a limitation with this approach and explain how the addition of an AND gatecan be used to resolve this problem. Briefly explain how this impacts on the memorymap.
A large endian byte addressed memory system with eight distinct memory modules is included in a computer system. Each memory module has 134217728 cells and is 32 bits wide. a) What is the 32-bit memory address of cell 1048578 in module 3 if the memory uses high order interleaving? b) What is the 32-bit memory address of byte 1048575 inside module 2 if the memory uses high order interleaving? c) What is the 32-bit memory address of cell 511 inside module 1 if the high order interleaved memory utilises little endian storage order instead of big endian storage order?
Can you show me step by step please
Question 1 The memory mapping arrangements of four memory devices in a microcontroller is given as (a) Your Device SD000-SD3FF RAM $D800-SDFFF ROM SE000-$FFFF I/O Ports $5800-S58FF (i) Determine the total memory space of each of the four devices. (ii) Design a fully-decoded positive-logic address decoder for all four devices. (iii) Design a minimal cost, positive-logic address decoder for a component Your Device in a small embedded microprocessor system
a) The circuitry of a microprocessor comprises conductive routes referred to as buses. As a consequence, current is permitted to flow between the various components. As a microprocessor specialist, classify and characterise these buses and their functions. b) In a microprocessor, what is the difference between data and instructions?
Using appropriate illustrations show how an 8255A could be connected to an 8051microcontroller I/O pins in memory-mapped and port-mapped configurations. Brieflyexplain the significance of the MOVX instruction in relation to these two configurations.