4) The nozte inlet Di =50mm otkt Dzo5mm う Dasred flow rete (9)-0.05m is P CPat) if P = 6 MP Hintd Vi.Ai =Vz Az=8 Hint2o As T D そえ what TT= 3 9: 9.8 Hint 3 s h in md? So mm

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: 4. The top of a male dovetail is 4 inches wide. If the angle is 55° and the depth is 5/8 inch, what…

A: 4.88''Explanation:Let's illustrate the problem,Given the width of the top of male dovetail which is…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: 3.00- 1.25-

A:

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: can you make a sketch of the solution

A:

Q: Referring to the object in Fig. 10, sketch the front, left, and section view following third angle…

A: (1) Analysis of ProblemTake a close look at the provided figure and understand the object's…

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: can you do the SF and BM calculation with explanations

A:

Q: 30o0mm*300 mmXJ0omm

A: Given data :- 300mm × 300mm × 300mm  Compare L × b × h  Here L= length           b= width…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: I need answers for problems 1, 2, and 3 pertaining to the print provided.

A: (1). Yes, the detail drawing is of a single part namely the Bonnet Sleeve.

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First 3. angle…

A: First draw the given front view and side view of casting.

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: Answer in number 7 and 8.

A:

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: what happened with the 10 in the first equation?

A:

Q: Draw a perspective,isometric(with 30 angle), & oblique(with 45 amgle) view of a cube.

A: Draw a perspective,isometric(with 30° angle), & oblique(with 45° angle) view of a cube.

Q: A two-degree-of-freedom system has O Many normal modes O One normal mode OTwo normal modes O Three…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: Question 79 CNC machine tools can have 5 axes, when O The rotating cutting tool can swivel (incline)…

A: Given that ,  CNC machine tool have 5 axis when ,

Q: How do you solve parts a,b and c?

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: Is this for number 1 only?

A:

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .