A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that speed?  (round to two decimal places)

Q: A motor with a 3-inch drive pulley is belt-coupled to an equipment that operates at 900 rpm and has…

A:

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A:

Q: What is the power output of a motor that provides a torque of 2,917 N*m while running at 2,641 rpm?…

A: The objective of this question is to calculate the power output of a motor given the torque and…

Q: What is the distance between the axles of the two pulleys?

A: Given that: diameter of smaller pulley = 250 mm diameter of larger pulley = 500 mm wrap angle = 120…

Q: Bicycle Physics Given: F = 60 lbs R₂-8 in R-5 in R₂-2 in Re-14 in Calculate F₂ T₂ F₂ T₂ F₂ T₂ F₂ T₂…

A: Write the given data. F1=60 lbsR1=8 inR2=5 inR3=2 inR4=14 inCompound Gear ratio=R1R2×R3R4

Q: tance travelled and is given icle is given by: 200s -s²)

A: we know that  a= dv/dt dv = a*dt

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A:

Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At…

A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:

Q: Chains are used in gears applications while belts are used with pulley systems. Select one: O True O…

A:

Q: y F1 = 30 N 3 4 F3 = 50 N 20° F2 = 20 N

A: From the data given in question, F1 = 30 N F2 = 20 N F3 = 50 N

Q: A torque of 11519 inch-pounds is applied to a 1 ¾ inch diameter steel shaft. Use modulus of…

A:

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: in the given system, as the result of AB crank arm's spinning, F gear is starting to have an…

A:

Q: F3 = 750 N 45° 5 30° F2 = 625 N F = 850 N

A:

Q: Two shafts, having axes in the same plane intersecting at an angle of 45 degrees, turn in opposite…

A:

Q: A stepper motor is used to drive an x-y milling machine table. If the step angle of the motor is 1°…

A: Given, Step angle of the motor, α=1°Pitch of the lead screw,p=7mmSpped, V=25.0mm/sDistance moved by…

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: Analytically determine the linear displacement of the piston in the compressor linkage shown in the…

A:

Q: Explain newtons third l

A: for every action their is equal and opposite reaction.

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a…

A: Given data: The time for car is t=5 min=300 sec The covered distance is s=181 m The diameter of the…

Q: The two gears in the picture below on the left are meshing together. The two gears in the picture on…

A: A-The two meshing gears have the same module. When two gear meshes, the module (which is defined as…

Q: 42 in 64 [in]- 50 in D 59 in 63 in +10 in ... 21 in SAR (

A: Given,

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.