4 - For the given frame and loading, find the reactions at supports A and E. The pin and slot mechanism at point D is frictionless. The contact condition at support A is also frictionless. C 0.4m B D 500N 0.4m A E 0.3m 0.3m 0.3m 0.3m fixed Support

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: 4. Consider steady flow of water through an axisymmetric garden hose nozzle (see Fig). Along the…

A: Given is  Flow is a steady flow Flow is an axisymmetric flow Fluid is incompressible Centreline…

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: SHAFT KEY

A:

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: a. Determine the magnitue of P and F (in N) if the resultant of the five force shown is 1000N…

A: The given system of force is as shown below, The given forces are as follows. F1=840…

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A: Given Gear train arrangement To find Gear train which will be effective for bearing

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm.   From the…

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A: As per given question  The radial distance measured from the pitch circle of a gear to the bottom…