4) A surface with No adsorption centers has N (S No) gas molecules adsorbed on it. Show that the chemical potential of the adsorbed molecules is given by u = kTin- where a(T) is the partition function of a single adsorbed molecule. Solve the problem by constructing the grand partition function as well as the partition function of the system. (Neglect the intermolecular interaction among the adsorbed molecules,)

4) A surface with No adsorption centers has N (S No) gas molecules adsorbed on it. Show that the chemical potential of the adsorbed molecules is given by u = kTin- where a(T) is the partition function of a single adsorbed molecule. Solve the problem by constructing the grand partition function as well as the partition function of the system. (Neglect the intermolecular interaction among the adsorbed molecules,)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3 An FCC iron-carbon alloy initially containing 0.35 wt% C is exposed to an oxygen-rich and virtually carbon- free atmosphere at 1400 K (1127 °C). Under these circumstances the carbon diffuses from the alloy and reacts at the surface with the oxygen in the atmosphere; that is, the carbon concentration at the surface position is maintained essentially at 0 wt% C. (This process of carbon depletion is termed decarburization.) At what position will the carbon concentration be 0.15 wt% after a 10-h treatment? The value of D at 1400 K is 6.9 x 10¹¹ m²/s.
True or False? Justify your answer. A. In a rectangular drug delivery device that consists of a drug reservoir and a diffusion barrier made of a polymer gel, the steady state diffusion (mass transfer) rate through a barrier of thickness 1 cm was found to be 20 mg/day. If the barrier thickness were to be doubled keeping the reservoir drug concentration the same, the mass transfer rate would be 10 mg/day. B. In a spherical drug delivery device consisting of a core reservoir surrounded by a polymer gel barrier, the steady state diffusion (mass transfer) rate through a barrier of thickness 1 cm was found to be 20 mg/day. If the barrier thickness were to be doubled keeping the reservoir drug concentration the same, the mass transfer rate would be 10 mg/day.
Diffusion of carbon into BCC iron for 12 hours at a temperature of 500 °C results in a carbon concentration of 0.2 wt% at a depth 2 mm from the surface. How long would it take to get a concentration of 0.2 wt% at a depth 3 mm from the surface at 500 °C?
Q1: A) : Oxygen (A) is diffusing through nondiffusing carbon monoxide(B) .The total pressure is 1*105 N/m2 and the temperature 298 k. The partial pressure of oxygen at two phases 3.0 mm apart is respectively 12000 and 7500 N/m?. The diffusivity of the mixture is 1.78 *10 5 m?/s. Calculate the rate of diffusion of oxygen in kmol/s through each square meter of the two planes. IR I. Resaleul f.ucion f oxugon (Al through
1. You have ice at 263 K (-10.0 °C) and 1.0 atm. Whatvcould you do to make the ice sublime? 2. A sample of dry ice (solid CO2) is cooled to 173 K (-100.0 °C), and is set on a table at room temperature (298 K; 25 °C). At what temperature is the rate of sublimation and deposition the same (assume that pressure is held constant at 1 atm)?
10.7 One of the Hume-Rothery rules for solid solutions11 is that the solubilityof solute B in solvent A becomes negligible when the atomic radii of A andB differ by more than 15%. Plot the maximum solubility (atomic percent) of Ni, Pt, Au, Al, Ag, and Pb as a function of the ratio of solute and solvent (Cu) radii, and verify that the solid solubility in Cu drops precipitously at a size ratio of about 1.15. Use the following data:rNi = 0.1246 nm rAl = 0.143 nmrAg = 0.1444 nmrPt = 0.139 nm rPb = 0.1750 nmrCu = 0.1278 nm rAu = 0.1441 nm
3. A block of pure iron needs to be converted to steel. The density of iron is 7.86x10^3kg/m^3, and the atomic weight is 0.0558kg/mol. The concentration of carbon at position A is 4x10^26 at/m^3. The carbon atomic weight is 0.012kg/mol. Carbon must be diffused into the iron to convert it to steel. It is desired to have 1025 atoms of carbon per m' at point B. Position A is 1mm from position B. Assume that you have 1m^3 of iron. You heat the material uniformly to 1200°C. Do, carton = 79x10 * m/sec, Ea = 83kJ/mol, and the density of carbon is 2260kg/m^3. (4pts) 1mm Fe block A What is Dearbon at 1200°C in m?/sec? i. ii. Calculate the FLUX (J) of carbon atoms in atoms per m²-sec at 1200°C? B.
Parvinbhai
For a steel alloy it has been determined that a carburizing heat treatment of 11.4h duration will raise the carbon concentration to 0.410 wt% at a point 2.10 mm from the surface. Estimate the time necessary to achieve the same concentration at a 4.60 mm position for an identical steel and at the same carburizing temperature. i