4) A deepwell pump delivers water in a distribution system, the total dynamic head of the pump is 250ft & the system flow rate is 200gpm. The efficiency of the deepwell pump and motor are 80% and 70% respectively. If the power consumption costs 20pesos per kW-hr, how much is the power consumption if the pump withdraws 7000 cubic meters of water?

4) A deepwell pump delivers water in a distribution system, the total dynamic head of the pump is 250ft & the system flow rate is 200gpm. The efficiency of the deepwell pump and motor are 80% and 70% respectively. If the power consumption costs 20pesos per kW-hr, how much is the power consumption if the pump withdraws 7000 cubic meters of water?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water must flow over a distance of 2800 m from a large catchment dam to a turbine. The water level…

A: P=300kW D=200mm f=0.007 L=2800m

Q: Q1: For a centrifugal pump has a power of 12KW, the efficiencies of the pump and are 60% and 80%…

Q: A single acting reciprocating pump operating at 140 rpm has a piston diameter of 220 mm and stroke…

Q: Q6/The average monthly inflow for a niver are shown in the table below. A-Draw flow duration curve…

Q: Q- Consider the following data relating to performance of a centrifugal pump: speed 1200 rpm, flow…

A: given- Centrifugal pump-N1=1200 rpmdischarge Q=30 L/sHead H=20 mPower P=5 kWN2=1500 rpm

Q: m/N of oil flowing, calculate the power delivered Suction pipe is 1.4 N-m/N of oil flowing,…

A: Given:- 840 L/min crude oil sg=0.85 total energy loss=4.2N-m/N To find:- pressure at the pump level…

Q: manufacturing facility consumes 40 m^3/h of water taken from a nearby river located 15 m below the…

A: Flow rate = 40 m3/hPipe diameter = 3 inchesPipe length = 240 mElevation head = 15 mPump efficiency…

Q: Problem 3 Water (20°C) is pumped through the 300-mm steel pipe from the lower tank to the upper one…

Q: A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The…

Q: Water is supplied at a height of 3m at the rate of 40 Lps to a hydraulic ram which delivers 31ps to…

Q: A hydroelectric dam is being planned with a Francis turbine. The engineers choose to geometrically…

A: The new turbine is geometrically similar to the existing turbine., The new penstock is also…

Q: 2. A centrifugal pump delivers 700 L/s of water against an elevation head of 40m when rotating at…

Q: Water must flow over a distance of 2 800 m from a large catchment dam to a turbine. The water level…

A: f = friction factor is their as default symbols and notations are used f=4f' f'= coefficient of…

Q: n the figure shown below, it is desired to pump 5408732 lit/day of water from a stream to a pool.…

A: hf1 = 10.67 Q1.852 L1C11.852 d14.8704 Q = 5408732 lit / day = 0.06 cu m/ s hf1 = 10.67 (0.06)1.852…

Q: Water from a reservoir is pumped over a hill through a pipe 90 cm in diameter, and a pressure of 200…

Q: Water must flow over a distance of 2 800 m from a large catchment dam to a turbine. The water level…

A: L=2800m D=200mm P=300kW

Q: A pump with horsepower (60 hp), gives a drainage of (0.360 m3 / s) of water, so that the height that…

A: Pump power = P = 60hp or 44.743kw Discharge = Q = .360 m3/s Pump hear = H = 10m

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 11-kW…

Q: Water is pumped through a pipeline to a height of 10 m at the rate of 0.1 m³/s, friction and other…

A: Given: Height of pump, H = 10 m Rate of flow, Q = 0.1 m3/s Friction and other minor losses or total…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate if 25 L/s by a 10 kW…

A: Ppump = 10Kwatt

Q: above at a rate of 25 L/s by a 12-kW (sha rreversible head loss of the piping syste mechanical…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A: Given Head = 45 m Flow rate = 0.03 m3/s Shaft power = 20 kW

Q: A pump delivers water at a rate of 0.025 m³/s against a head of 30 m. If the overall efficiency of…

A: Given data : Head (h)=30 mFlow rate (Q)=0.025 m3/sEfficiency (η)=75%

Q: A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The…

Q: (a) total pumping head in meters, (b) the power required by the pump, and (c) the monthly power cost…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A: To Determine a) The mechanical energy required to maintain the water flow, b) mechanical power that…

Q: Q110. A hydropower plant has to work under the following conditions. Determine the likely number of…

Q: determine the discharge inside the pipe in liters per second

Concept explainers

Components of Hydroelectric Power Plant

A hydro electric power plant derives the energy from the force of fast moving water to harness energy. The demand for energy needs has impacted the environment resulting in global warming. Extensive use of non-renewable energy sources like petrol and diesel is the primary reason for environmental pollution. A major shift from non-renewable energy sources to renewable energy sources is the only solution to encounter the rising issue of environmental damage.

Question

4) A deepwell pump delivers water in a distribution system, the total dynamic head of
the pump is 250ft & the system flow rate is 200gpm. The efficiency of the deepwell
pump and motor are 80% and 70% respectively. If the power consumption costs
20pesos per kW-hr, how much is the power consumption if the pump withdraws 7000
cubic meters of water?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The water taken from a stream at an average speed of 5 m/s is transferred to the turbine by a forced (pressurized) pipe system in order to generate electrical energy. After passing through a 10 m3/s flow rate turbine passing through a pressure pipe, it is poured into the lake downstream. the total irreversible (irreversible) load (energy) loss Dec the piping system between points 1 and 2 (excluding the turbine) is determined as 8 m. Calculate the theoretical and actual power of the turbine by taking the efficiency of the turbine generator set, η = 0.85.
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?
A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The difference in elevation between the two reservoirs is 120ft. For a design flowrate of 50ft^3/s, the head loss is 30ft. Solve the efficiency of the turbine if the actual energy extracted is 100hp. Neglect the difference in atmospheric pressure between the reservoirs. O 24.90% O 35.60% O 40.80% O 19.60%
2. Consider the system described in the news: at night, when there is energy left, water is pumped from a large lake to a reservoir at 80 m above the lake level. During the day, this water is used to generate energy in a turbine located 80 m below the elevated reservoir. Considering that the water flow is always 5000 liters/s (both at the inlet of the reservoir and at the outlet) and that the pump and turbine efficiencies are 70%, what is the power (in kW) required by the pump and the power (in kW) recovered in the turbine. Data: The pipe diameter is always the same along the system (d = 0.5 m); g = 10 m/s2; γ = 9810 N/m3. Matter transport phenomena; Please make it typeable as handwriting interferes with understanding
Water must flow over a distance of 2 800 m from a large catchment dam to a turbine. The water level in the catchment dam is 1 620 m above sea level and the turbine is situated 1 275 m above sea level. The efficiency of transmission is 65% and 300 kW must be transmitted from the pipeline to the turbine. If f = 0.007, determine the number of 200 mm diameter pipelines, which must be laid in parallel, needed to transmit the required power.
A single acting reciprocating pump has a plunger of diameter 250 mm and a stroke of 350 mm. If the speed of the pump is 60 rpm and it delivers 16.5 lit/sec of water against a suction head of 5 m and a delivery head of 20 m, what is the co- efficient of discharge?
I need the answer as soon as possible
For a 100 MW hydro power plant, calculate the water volumetric flow ratefor the 3 head values of 50m, 100m and 300m. Assume effective head to be85% of the gross head.
1. Determine the power required to drive a centrifugal pump which discharges water at the rate of 200 liters per minute against a total head of 22m. Take overall efficiency of the pump as 70 %