•4-33. The steel pipe is filled with concrete and subjected to a compressive force of 80 kN. Determine the average normal stress in the concrete and the steel due to this loading. The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. Eg = 200 GPa, E̟ = 24 GPa. 80 kN 500 mm

Q: The cantilever strut is subjected to the point loads P1 = 1.4 kN and P2 = 2.8 kN. Determine the…

A: A loading beam With LoadsP1=1.4 kNP2=2.8 kNTo determine: Shear stress at point B

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

A:

Q: A vertical arm pinned at A is supported by wire BC. If the arm is pulled such that it rotates…

A:

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm  the bar thickness (t) = 15 mm. Each…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: The solid circular rod has a cross-sectional area of 420 mm². It is subjected to a uniform axial…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a…

A: The cross sectional area of steel hoop is  The allowable stress of hoop is The diameter of wood pipe…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.