300 mm -700 mm and brake bar is = 0-4. If the moment %3D -125 mm M = 35 N-m, determine the smallest force P that s00 mm needs to be applied to the brake bar in order to prevent the drum from rotating. Also determine the corresponding horizontal and vertical components of reaction at pin 0. Neglect the weight and thickness of the brake bar. The drum has a mass of 25Kg.

300 mm -700 mm and brake bar is = 0-4. If the moment %3D -125 mm M = 35 N-m, determine the smallest force P that s00 mm needs to be applied to the brake bar in order to prevent the drum from rotating. Also determine the corresponding horizontal and vertical components of reaction at pin 0. Neglect the weight and thickness of the brake bar. The drum has a mass of 25Kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6-127. Determine the clamping force exerted on the smooth pipe at B if a force of 20 lb is applied to the handles of the pliers. The pliers are pinned together at A. 20 lb 20 lb 10 in. 40° 1.5 in. 0.5 in. B
4-34. If the cable can be subjected to a maximum tension of 1.5 kN, determine the maximum force F which may be applied to the plate. Compute the x, y, z components of reaction at the hinge A for this loading. 0.3 m 02m X0.1 m 03m 0.9 m
The pumping unit is used to recover oil. When the walking beam ABC is horizontal, the force acting in the wireline at the well head is Fc = 250 lb. Determine the torque M which must be exerted by the motor in order to overcome this load. The horse-head C weighs 56 lb and has a center of gravity at Gc. The walking beam ABC has a weight of 130 lb and a center of gravity at GB, and the counterweight has a weight of 190 lb and a center of gravity at Gw. The pitman, AD, is pin connected at its ends and has negligible Figure 1 of 1 5 ft 6 ft 1 ft GB 70 G20 250 Ib 3 ft 2.5 ft Part A Determine the torque M which must be exerted by the motor. Express your answer to three significant figures and include the appropriate units. HA ? Value M %3D Units Submit Request Answer 國
please help me, thank you
A woman is holding a 3.7-kg sphere in her hand with the entire arm held horizontally as shown in the figure. A tensile force in the deltoid muscle prevents the arm from rotating about the shoulder joint O; this force acts at the 21° angle shown. Determine the x- component of the force reaction at the shoulder joint O. The mass of the upper arm is my = 1.9 kg, the mass of the lower arm is m₁ = 1.1 kg, and the mass of the hand is my = 0.4 kg; all the corresponding weights act at the locations shown in the figure. Calculate your answer with one decimal figure accuracy. g = 9.81 m/s². Deltoid muscle FD 21° 125 mm 130 mm WU 412 mm- y 1 I L- 635 mm YW₂ Ws WH
P5-3. then draw the free-body diagrams of each member of the identify any two-force members, and frame. 800 N 200 N/m 6 m- -2 m m-
The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. P А 36° d He = 0.50 2.1 d Answer: P = i mg
The constant moment of 100 Nm is applied to the crank shaft. Determine the compressive force P that is exerted on the piston for equilibrium as a function of θ. Plot the results of P (ordinate) versus θ (abscissa) for 0° ≤ θ ≤ 90°. Draw FBD.
If d=2m and F-200N and the mass of ball 30 kg Determine the forces in cables AC and AB in equilibrium 1.5 m F -2 m- Maximum size for new files: 128MB
The 428-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4202 N, Q = 3387 N, T = 40694 Nm, x = 1.14 m, y = 1.53 m, and z = 1.46 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.
Consider the following system in static equilibrium. Force vector Facts at a distance from the pin support at point O. Draw appropriate FBD as necessary. Assume frictionless pulleys If the reaction forces at O is zero and magnitude F is 169N, a. Find F and "a". (F need not necessarily be in the 4 quadrant as shown below) b. Find reaction forces at B. 4m Im 5m 12
* Incorrect Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 685 lb in the y-direction, determine the necessary values of T and 0. Assume F₁ - 355 lb, F₂= 255 F₁ Answers: T= 0- i 35.31 i 983.11 lb, F3-400 lb, = 34° DI lb O T F₁