5-87. Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaction at the journal bearing C and thrust bearing D if 0 = 45°. The bearings are in proper alignment and exert only force reactions on the shaft.

5-87. Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaction at the journal bearing C and thrust bearing D if 0 = 45°. The bearings are in proper alignment and exert only force reactions on the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P5-3. then draw the free-body diagrams of each member of the identify any two-force members, and frame. 2 m 400 N в 0.2 m 1.5 m
3-38 with the following modification change the block weight to 50 lb
5-78. The hatch door has a weight of 80 lb and center of gravity at G. If the force F applied to the handle at C has coordinate direction angles of a = 60°, ß = 45°, and y = 60°, determine the magnitude of F needed to hold the door slightly open as shown. If the hinge at A becomes loose from its attachment and is ineffective, what are the x, y, z components of reaction at hinge B? 2 4 ft 3 ft. 2 ft 3 ft C B X F Probs. 5-77/78
4-32. Determine the force P of Fig. P4-32 that will maintain equilibrium. 400lb P4-32
4-3. Determine the reactions at the supports. S00 N/m
5-67. Due to an unequal distribution of fuel in the wing tanks, the centers of gravity for the airplane fuselage A and wings B and C are located as shown. If these components have weights WA = 45 000 lb, WR = 8000 lb, and We = 6000 lb, determine the normal reactions of the wheels D, E, and Fon the ground. 8 ft F 6 ft 8 ft 6 ft 4 ft 20 ft 3 ft
*5-16. Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A. The pulley at D is frictionless and the cylinder weighs 80 lb. A 5 ft- D B 2 5 ft 3 ft Prob. 5-16 C
4-21. The uniform beam has a weight Wand length / and is supported by a pin at A and a cable BC. Determine the horizontal and vertical components of reaction at A and the tension in the cable necessary to hold the beam in the position shown.
Determine the components of reaction at D. Take that PP_1 = 11 kN and P_2 = 18 kN .
- The unifom bar OC of lmgth L md mass (m) pivots freely about a horizontal axis through O. If the spring of modulusk is unstretched when C is coincident with A, detennine the tension T roquired to hold the bar in the position shown. The diameter of the small pulley at D| is negligible. L/2 L/2
R5-5. Determine the x, y, z components of reaction at the fixed wall A. The 150-N force is parallel to the z axis and the 200-N force is parallel to the y axis. x Z 2 m 150 N 1 m 2 m 2.5 m -200 N
The uniform steel beam of mass m = 19.6 kg and length I= 780 mm is suspended by the two cables at A and B. If the cable at B suddenly breaks, determine the tension Tin the cable at A immediately after the break occurs. Treat the beam as a slender rod. Assume e = 56°. Answer: T = N