31-40. The weight W of a traveling crane is 20 tons acting as shown in the figure. To prevent the cranefrom tipping to the right when carrying a load P of 20 tons, a counterweight Q is used. Determine the valueand position of Q so that the crane will remain in equilibrium both when the maximum load P is appliedand when the load P is removed.W = 20 tonsP = 20 tonsex * 5' 10

The load acting the crane is given as, P=20 tons.

31-40. The weight W of a traveling crane is 20 tons acting as shown in the figure. To prevent the cran from tipping to the right when carrying a load P of 20 tons, a counterweight Q is used. Determine the valu and position of Q so that the crane will remain in equilibrium both when the maximum load P is applie and when the load P is removed. 20 tons P= 20 tons

31-40. The weight W of a traveling crane is 20 tons acting as shown in the figure. To prevent the cran from tipping to the right when carrying a load P of 20 tons, a counterweight Q is used. Determine the valu and position of Q so that the crane will remain in equilibrium both when the maximum load P is applie and when the load P is removed. 20 tons P= 20 tons

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spring with a torsional stiffness k is attached to the hinge at B. It is unstretched when the rod assembly is in the vertical position. Determine the weight W of the block that results in neutral equilibrium. Hint: Establish thepotential energy function for a small angle θ, i.e., approximate sin θ ≈ 0, and cos θ ≈ 1 - θ2/2.
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3
:Determine the force P needed to lift the load. Also, determine the proper placement x of the hook for equilibrium. Neglect the weight of the beam. 0.9 m 100 mm- 100 mm 100 mm C B 6 kN
The mass center G of the 1390-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1393 mm- 913 mm Answers: Normal force under each of the front tires: Nf = i Normal force under each of the rear tires: N, = i
The mass center Gof the 1490-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1290 mm-976 mm- Answers: Normal force under each of the front tires: N; = i N Normal force under each of the rear tires: N, = N z z
The frame shown is supported by a hinge (pin) at A and a roller at E. the frame is subject to three forces F1 = 410 N, F2 = 190 N and F3 = 250 N as shown in the figure below. If the frame is in equilibrium, Determine 1.25 m F2 3 m 2 m 2 m F3 A. Reactions at A Ax = Ay = B. Reactions at E Ex = Ey =
The uniform rod AB has a mass of 140-kg and it is supported as shown in the figure. If the applied force F= 1.4 kN, what is the reaction at A on rod AB? Assume frictionless surfaces. 1.5 1.5 0.9 m 0.9 m
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension Tin cable CD? 3.7' Answers: LCD= TCD= i i A 48° B 69 lb ft lb D
Determine force FB when holding the 5-lb stone in equilibrium. The stone has a center of mass at G. В H FB 75 Fc 0.8 in. 2 in. |-– 14 in.