etermine the vertical reactions at each of the two outriggers as a function of boom angle when the boom is carrying a 1.2 Mg load and th

Q: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: Given the weight of door and the position of door.  Required: F, A and B

Q: The light right-angle boom which supports the 260-kg cylinder is supported by three cables and a…

A: The mass of cylinder is m=260 kg

Q: The shear leg derrick is used to haul the 200-kg net of fish to the dock. Determine the compressive…

A: Solution.jpg

Q: platform scale consist of a combination of third and first class levers so that the load on one…

A: The free-body diagram for AB is-The moment equilibrium condition about point A-

Q: The light right-angle boom which supports the 560-kg cylinder is supported by three cables and a…

A:

Q: X Incorrect The 54-kg homogeneous smooth sphere rests on the 20° incline A and bears against the…

A:

Q: Problem Statement Based on Problem 6-11 from the textbook. The spring has an unstretched length of…

A:

Q: The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: The weihght of rectangular plate is .

Q: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: Here G represents the center of gravity Following data is provided Weight of the door W=50 lb a=26…

Q: The 570-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: The ends of the three cables are attached to a ring at A and to the edge of the uniform plate.…

A: Draw FBD

Q: The light right-angle boom which supports the 550-kg cylinder is supported by three cables and a…

A:

Q: The mass center G of the 1235-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: 2. The wall crane supports a horizontal and vertical compo D. Also, what is the force in ABC has a…

A: The force equilibrium at point E is-

Q: The jib crane is pin connected at A and supported by a pin connected collar on smooth rod at B. If x…

A: According to the given data x=6ft AB=12ft W=5500lb We need to fin Reaction at point A and B

Q: The shear leg derrick is used to haul the 200-kg net of fish to the dock. Determine the compressive…

A:

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A:

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: Determine the reactions at the support. There are two supports: a collar that can slide along the…

A:

Q: The mass center G of the 1220-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: 1- Determine the angle 8 for equilibrium and investigate the stability of the mechanism in this…

A: given :spring is unstretched,when mass of block A= m= 40 kgspring stiffness= k= 1.5 kN/m

Q: Determine the tension in each cable necessary for equilibrium of the massless pipe supporting 800…

A: Uniform load applied on pipe:Total length of the uniform load:And structure is symmetric about XZ…

Q: The ramp of a ship has a weight of 250 lb and a center of gravity at G. Determine the cable force in…

A: Given: W = 250 lb

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.