1- Determine the angle 8 for equilibrium and investigate the stability of the mechanism in this position. The spring has a stiffness of k = 1.5 kN/m and is unstretched when 8 = 90°. The block A has a mass of 40 kg as shown in Fig.1. Neglect the mass of the links. quin 600 mm 450 mm

Q: If the cart's mass is 32 kg and it is subjected to a horizontal force of P-90 N. determine the…

A:

Q: 5-37. The cantilevered jib crane is used to support the load of 780 lb. If x= 5 ft, determine the…

A:

Q: Determine the magnitude of the vertical reaction force at D. Assume a = 4.9 ft, b = 9.8 ft, c = 19.6…

A:

Q: solve  this 3D    RIGID    BODY    EQUILIBRIUM please

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine internal reaction at the point located between A and C, 0.7 m to the right of A. Disregard…

A:

Q: Q2/ Determine the unstretched length of spring AC if a force P 801b causes the angle 0 = 60° for…

A: Solution:

Q: Now, for the same J-shaped member, determine MA, MA and MA, the couple moments at the support about…

A:

Q: The rod supports a weight of 100 lb and is pinned at its end A. It is also subjected to a couple…

A:

Q: The 0.6 m uniform slender bar has a mass of 5 kg. Two springs 1 and 2 having stiffness k, = 80 N/m…

A: Given Data: Slender bar length L=0.6 m slender bar mass m = 5 kg Spring Stiffness are k1=80 N/m and…

Q: 3. Three kids stand on a see-saw as shown. The see-saw has a uniform cross section and weighs 10 lb,…

A: Given Data  mA= 30 lb mB= 40 lb mC=20 lb

Q: The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position as…

A: Given :unstretched length of spring AB is 3 mFrom the figure , the stretched length of spring AB LAB…

Q: The mass center G of the 1540-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: The mass center G of the 1235-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: 1.5 m B 1.5 m I m 2.5 m 3 m -- 1.5 1.5 m-1 mª| 3 m

A: given data: w=900N/m total weight=900*3=2700N

Q: determine the magnitude of the resultant force ( in SI Unit ) acting on the bracket and its F;= 300…

A: Given, ϕ=400F1=150 N Let the force F2 makes an angle α with the horizontal Therefore sinα=35cosα=45…

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A:

Q: Based on Problem 5-87 from the textbook. Both pulleys are fixed to the shaft and as the shaft turns…

A:

Q: 600 lb C 18 25 750 lb-ft B 10 900 lb| Dimensions in inches

A:

Q: PROBLEM 3 Given the frame to the right. There are pins at A and C. Solve for the reactions at A and…

A:

Q: Need help, include all steps and units please and thanks.

A: Create a free-body diagram at the joint where the cables meet.Since the pulley is frictionless, the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.