30B2 m-2 m-2 m•1-61. Determine the maximum magnitude P of the loadthe beam will support if the average shear stress in each pinis not to allowed to exceed 60 MPa. All pins are subjected todouble shear as shown, and each has a diameter of 18 mm.

Answered: Image /qna-images/answer/9983fca8-a714-4448-8789-3dcaf3bb9201.jpg

Answered: 30° •1-61. Determine the maximum…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joist are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is s allow = 1700 psi, determine the smallest height h so that the beam will support a load of P = 600 lb. Also, will the entire joist safely support the load? Neglect the stress concentration at the notch.
If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress developed on the cross section of the supporting member at section a- a, where L= 700 mm, and the radius r= 30 mm. Section a - a 98.089 MPa O 49.564 MPa 8.665 MPa 96.009 MPa O 96.945 MPa O 97.049 MPa
1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is Tail 350 MPa. Use a factor of safety for shear of F.S. = 3 40 kN 40 KN 30 mm 80 KN 30 mm
The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume L = 1.1 m and 0 = 20°. If the average shear stress in the pins at A, B, and C cannot exceed 125 MPa, determine the maximum distributed load Wmax that can be supported by the structure. (1) 0 Answer: Wmax i B kN/m C
Determine the required diameter of the pins at A and B if the allowable shear stress for the material is tallow = 100 MPa. Both pins are subjected to double shear.
The beam is constructed from three boards. Determine the maximum loads P that it can support if the allowable shear stress for the wood is tallow = 400 psi. What is the maximum allowable spacing s of the nails used to holdthe top and bottom flanges to the web if each nail can resist a shear force of 400 lb?
All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support
The elbow of the pipe has an outer radius of 0.75 in. and an inner radius of 0.63 in. If the assembly is subjected to the moments of M = 25 lb # in., determine the maximum stress at section a–a.
The three suspender bars are made of steel and have equal cross-sectional areas of 450 mm?. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A В C 80 kN 2 m 50 kN D E -1 m- +1m- 1m-1 m-|
The beam has a square cross section and is made of wood having an allowable shear stress of Tallow= 1.4 ksi. If it is subjected to a shear of V= 1.5 kip, determine the smallest dimension a of its sides. Sketch the shear stress distribution acting across the beam's cross section. Hint: Construct the stress distribution in 2D similar to in-class examples, rather than isometrically similar to the textbook examples for clarity. V = 1.5 kip
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.375 in. Assume L = 5.0 ft. If the average shear stress in the bolts cannot exceed 60 ksi, determine the maximum distributed load Wmax that can be supported by the structure. (1) Answer: Wmax = L B kips/ft
Current Attempt in Progress The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 22 mm. Assume L = 1.5 m and 0 = 25°. If the average shear stress in the pins at A, B, and C cannot exceed 105 MPa, determine the maximum distributed load Wmax that can be supported by the structure. A (1) W L Answer: Wmax i B kN/m

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

30° •1-61. Determine the maximum magnitude P of the load the beam will support if the average shear stress in each pin is not to allowed to exceed 60 MPa. All pins are subjected to double shear as shown, and each has a diameter of 18 mm. 2 m- -2 m -2 m