3.4-5 A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T, = 1000 lb-in., T= T - 500 lb-in., and 7, Ts 800 lb-in. The tube has an outside diameter d = 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0f. Determine the maximum permissible inside diameter d, of the tube. Ts 1000 Ib-in. 500 lb-in. 800 Ib-in. 500 Ib-in. 800 lb-in.

3.4-5 A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T, = 1000 lb-in., T= T - 500 lb-in., and 7, Ts 800 lb-in. The tube has an outside diameter d = 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0f. Determine the maximum permissible inside diameter d, of the tube. Ts 1000 Ib-in. 500 lb-in. 800 Ib-in. 500 Ib-in. 800 lb-in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 20 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 15 ksi. The normal stress magnitude in steel rod (2) must be limited to 33 ksi. The normal stress magnitude in brass rod (3) must be limited to 22 ksi. Determine the minimum diameter required for each of the three rods. (1) R В D di in. d2 = i in. dz = i in.
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
a uniform bar 1 is connected to a tapered rod 2. both are subjected to axial loads as shown. if P=7 kN, determine the axial deformation of tapered rod 2 (in mm). indicate negative sign if compression
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa