3.35 The clectric motor exerts a 500 N•m-torque on the aluminum shaft ABCD when it is rotating at a constant speed. Knowing that G = 27 GPa and that the torques exerted on pulleys B and Care as shown, determine the angle of twist between (a) B and C, (1)) B and D. 300 N.m 200 N - m 4S min 0.9 m 44 mm 1.2 m 40 mm

3.35 The clectric motor exerts a 500 N•m-torque on the aluminum shaft ABCD when it is rotating at a constant speed. Knowing that G = 27 GPa and that the torques exerted on pulleys B and Care as shown, determine the angle of twist between (a) B and C, (1)) B and D. 300 N.m 200 N - m 4S min 0.9 m 44 mm 1.2 m 40 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.4: Consider the shaft shown attached between two walls A and E. Determine the two torques at supports A and E knowing the segment has the same diameter of 25 mm. Assume the G = 80 GPa. 500N.m 200N.m A В C E 0.25 m 0.3 m 0.5 m
3.3 plz
Please help me.. urgent
w=15
OA A:YA دكوز شعبة B.png Knowing that the lengths of the shown solid shafts are AB=60mm and BC=80mm, determine the torque TA if the total angle of twist of disk A relative to the ground C is 3º. What are the corresponding shearing stresses for each shaft? Take G=77 MPa. TA 30 mm В TR = 400 N. m 46 mm II
A torque of 3 kN.m is applied to the steel shaft (G = 75 GPa). Determine the voltage ofmaximum shear as well as the angle of twist, knowing that a = 50 mm.
300 N.m 500 N.m B 0.4 m 0,6 m Fig. P3.48 0.3 m PROBLEM 3.48 The electric motor exerts a torque of 800 Nm on the steel shaft ABCD when it is rotating at constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D should not exceed 1.5°. Knowing that tmax S 60 MPa and G = 77 GPa, determine the minimum diameter shaft that may be used. [Ans. 42.1 mm] PROBLEM 3.52 14/04/2022 BANG 6 OLUESEN delete home end pg up pg dn num 9 + backspace * lock
answer by step thanks..
The aluminum rod AB (G= 27 GPa) is bonded to the brass rod BD(G= 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A.
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
3.11 Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod, determine (a) the shaft in which the maximum shear- ing stress occurs, (b) the magnitude of that stress. 48 N. m 144 N. m A Fig. P3.11 and P3.12 dAB 60 Nm B = 15 mm dBC C = 18 mm D dcp = 21 mm
4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7 x 106 psi for aluminum and 5.6 x 106 psi for brass, determine the maximum shearing stress (a) in cylinder AB, (b) in cylinder BC. Aluminum- 12 in. <-1.5 in. B T = 12.5 kip-in. Brass -2.0 in. C 18 in.