4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7 x 106 psi for aluminum and 5.6 x 106 psi for brass, determine the maximum shearing stress (a) in cylinder AB, (b) in cylinder BC. Aluminum- 12 in. -1.5 in. B T= 12.5 kip-in. Brass -2.0 in. C 18 in.

4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7 x 106 psi for aluminum and 5.6 x 106 psi for brass, determine the maximum shearing stress (a) in cylinder AB, (b) in cylinder BC. Aluminum- 12 in. -1.5 in. B T= 12.5 kip-in. Brass -2.0 in. C 18 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A chain block is hanged on a pin which is supported by plates on both side as shown. If the maximum safe load capacity is 3000 lb, determine (a) the shearing stress on the shaft having a diameter of 1.75 in. (b) and the thickness of the plates if the bearing stress on the plates is 20% greater than the shearing stress.
1. The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow = 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. B FAB 12 kip 8 in. FBD
The compressed-air tank AB has a 250-mm outside diameter and an 8-mm wall thickness. It is fitted with a collar by which a 40-kN force P is applied at B in the horizontal direction. Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum normal stress and the maximum shearing stress at point K. (Round the final answers to one decimal place.)
Question 3. A 4 by 4-in. wood-post BC is connected to a 1-in. diameter steel eye-bar AB to form a hoist. A load of w = 7000 Ibs is applied at point B on the hoist. (a)Determine the axial stresses in members AB and BC. (b) Determine the cross shearing stress in the 1-in. diameter bolt at point A. STEEL V -7000 lb WOOD FIG. I A
6. A rigid plate of negligible mass rests on the middle spring which is higher than the two outer springs by 20 mm. The middle spring consists of 24 turns of 25-mm diameter wire on a mean diameter of 150 mm. The two outer springs have 16 turns of 12-mm diameter wire on a mean diameter of 100 mm. Determine the shearing stress developed in each spring if P = 5 kN is applied. Use the Approximate formula. Use = 83 GPa. P=5 KN 20mm
w=15
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed
SECTION B(1) Question 1 The bell crank CBA is connected to a pin support B in double shear with 8-mm diameter pin B and to the 10-mm diameter rod CD. Knowing that the ultimate shearing stress is 110 MPa for the steel used in pin B and the ultimate normal stress is 230 MPa for the steel used in rod CD. Determine the maximum vertical force P that can be applied if an overall factor of safety of 1.5 is desired. 45% 300 mm B Figure 1 -450 mm-
Two wooden planks, each 1212 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.8 ksi, determine the magnitude P of the axial load that will cause the joint to fail. The magnitude P of the axial load that will cause the joint to fail is kips.
Determine the maximum shearing stress and elongation in a helical steel spring composed of 25 turns of 25-mm-diameter wire on a mean radius of 150 mm when the spring is supporting a load of 2.0 kN. Use Eq. A.M.Wahl Formula and G = 83 GPa.
Pravinbhai
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.