Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used to transmit power of (2.5 h.p) at speed of (46 r.p.m). Determine the required diameter of the shaft if knowing that the shaft made of :- 1-Steel with allowable shearing stress of (90MPa) and modulus of rigidity of (77GPa). 2- Bronze with allowable shearing stress of (35MPa) and modulus of rigidity of (42GPa).

Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used to transmit power of (2.5 h.p) at speed of (46 r.p.m). Determine the required diameter of the shaft if knowing that the shaft made of :- 1-Steel with allowable shearing stress of (90MPa) and modulus of rigidity of (77GPa). 2- Bronze with allowable shearing stress of (35MPa) and modulus of rigidity of (42GPa).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. If the solid shaft is made from a red brass alloy having an allowable shear stress of Tallow = 4 ksi, determine the maximum allowable torque T that can be applied at B. (please note that the problem is statically indeterminate!) 2 ft 4 in. 2 in. T 2 in. 4 ft
Please answer complete
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). ... 10 lb-ft 50 lb-ft 70 lb-ft |(1) 30 lb-ft A (3) B C D
A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB. The allowable shear stress in the steel is 6000 psi.Calculate the required speed of rotation (number ofrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.
Pravinbhai
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.
A 0.75" diameter solid steel shaft is connected by the steel bolted coupling shown. The maximum allowable shear stress in the steel is 18 ksi (shaft and bolts). The coupling consists of steel bolts that are 1/8" diameter and the bolt holes are equally spaced and centered on a 4" diameter circle (2" radius from the center of the shaft to the center of a bolt hole). Determine a) The maximum torque that the shaft can carry Ans: /,491"* b) The number of bolts required for the torque in part a). Assume the bolts fail by shearing at the coupling interface and the shear stress is uniform across the bolt's cross sectional area.
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
Need only handwritten solution only (not typed one).
A composite shaft is comprised of an inner solid steel shaft 1/6 ft in diameter slipped over with a hollow bronze shaft of 1/4 ft outer dimater and 1/6 ft inner diameter and of the same length as the steel shaft. The two shafts are then fastened rigidly together at their ends. For steel, G = 12 × 106 psi, and for bronze, G = 6 × 106 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 12,000 psi in the steel or 8,000 psi in the bronze?