3. Two spur gears transmit 36kW with a velocity ratio of2:1. The speed of the smaller driving gear is 100rpm.The centre distance between the shafts is to be asnear as possible to 920mm. If m=10 and -21MPa,determinea)Diameter of the shafts [120mm]123xb) PCD for each wheel [614mm; 1228mm] 1310c) Number of teeth on each wheel [61;122]d) Actual centre distance [921mm]e) Width of the teeth [313mm]

Answered: Image /qna-images/answer/03605585-9eef-4710-8c32-56551483e72e.jpg

3. Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and 21MPa, determine a) b) 123x Diameter of the shafts [120mm] PCD for each wheel [614mm; 1228mm] 1,310 Number of teeth on each wheel [61;122] d) Actual centre distance [921mm] e) Width of the teeth [313mm] c)

3. Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and 21MPa, determine a) b) 123x Diameter of the shafts [120mm] PCD for each wheel [614mm; 1228mm] 1,310 Number of teeth on each wheel [61;122] d) Actual centre distance [921mm] e) Width of the teeth [313mm] c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Example 8-2 Fig 8-10 shows a planetary gear train, in which the numbers of teeth of gears are z₁-100, z₂=101, Z₂-100, z3-99 .Determine the gear ratio iH1- 2' 2 H Fig. 8-10 Train with two pairs of external gears (双排外啮合周转轮系) 3
Q1a
Keino Thompson Problem 1. Given 2 parallel shalts with Required : h₁ = 3001pm d₁ N₁ = T₁ = + e = a) N₁ & N₂ b) p = center distance of 12.7 cm h₂ = 0.2 h₁ P = N₁ d₁ Power = = W d₂ Circular pitch of 10 teeth 2 Hp (Transmitted to pulley 2) gears in c) ng in rpm d) Pitch line velocities of Gears 1&2 of pulley 2 e) Torque in nm
An electric motor develops 6 HP at 3000 rpm. An 18 tooth gear is fitted to its shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 100 Nm is required? Answer: Ti vious page Next page https://learnonline.gmit.ie/mod/quiz/attempt.php?attempt-126637&cmid-1429658page-3# CHao Search for anything FI1 F10 F8 F9
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth Calculate the output angular velocity at Gear D (ωD). Give your answer in rads-1to the nearest radian.
A motor is driving an output shaft through a single-stage gears, as shown. Input Gear, N, Motor To Output Gear, N2 Number of teeth of the input gear, N1 = 24; Number of teeth of the output gear, N2 = 48; Gear efficiency = 95%; %3! If the output shaft is to deliver torque To = 20 Nm, calculate the torque required on the input shaft, Ti. Give your answer in Nm to 1 decimal places.
please help
How do you calculate the velocity ratio of revolutions per minute for the gear C
Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force Solution: (To be discussed by the Instructor during the lecture period)
Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A. Gear AB C D E ய ட ¡A Direction CW (a) (b) (c) (d) (e) B ic Number of teeth (f) 18 (g) 16 (h) 40 Determine the value of item (f) E iD iF Diametral Pitch 4 (j) (k) (1) 6 (m) A/ Pitch Diameter 7.50" (n) 10.00" 3.20" 8.00" (p) Speed (RPM) Center Distance (9) (w) (r) (s) (x) (t) (u) (y) (v)
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
An electric motor develops 8 HP at 2652 rpm. An 19 tooth gear is fitted to its output shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 92 Nm is required? Answer: Next page page Finis Time 9Type here to search