Question 3 a) A driver and a driven gear meshes with each other with the parameters shown in Table 1 below. i. Calculate the Gear ratio ii. Identify the values of a b.c.d Table 1 Pitch diameter No. of gear Speed of Angular Pitch linear of gear, D teeth, N gear, n velocity, w velocity, v Gear P (driver) 13 ст 15 450 RPM d Gear G (driven) a 20 b 0.7 rad/s b) A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min anticlockwise. The input power is 25kW and the efficiency is 90%. Compute i. the input torque ii. the output power iii. the output torque

Question 3 a) A driver and a driven gear meshes with each other with the parameters shown in Table 1 below. i. Calculate the Gear ratio ii. Identify the values of a b.c.d Table 1 Pitch diameter No. of gear Speed of Angular Pitch linear of gear, D teeth, N gear, n velocity, w velocity, v Gear P (driver) 13 ст 15 450 RPM d Gear G (driven) a 20 b 0.7 rad/s b) A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min anticlockwise. The input power is 25kW and the efficiency is 90%. Compute i. the input torque ii. the output power iii. the output torque

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Gear box in a car is shown in Figure Q(2). Using Tables given below and an input speed (Gear 2) of 3000 rev/min, Determine the following: (i) The number of teeth (z) in gears 3, 6, 7 & 11. Stages Gear No of Diameter Speed Ratio (Rv) (Ratio of output gear speed to input gear speed) teeth (Z) 2 3 15 1 120 mm 0.375 4 7 36 75 mm 1.5 6 3. 1 10 17 11 4 0.5 44 The drive shaft speed for third gear drive (2-3-4-7) (ii) The drive shaft speed for reverse gear (2-3-6-10-11-9) (iv) The module (m) of stage 1 Input Output Sequence Gear Drive First 2-3-6-9 Second 2-3-5-8 Third 2-3-4-7 Fourth Straight through Reverse 2-3-6-10-11-9 Figure Q(2)
please help me calculate the velocity ratio
Please help me asap
i need the answer quickly
You design a gearbox with a gear ratio of 5 (GR=5=TGB/Tm) to pull a load (FL) of 76 lbf using a motor and winch (rw=0.25 inches). What is the torque experienced by your motor when pulling the mass up at a constant speed in lbf ft? Note the units
control system pease answer as soon as possible
Example 8-2 Fig 8-10 shows a planetary gear train, in which the numbers of teeth of gears are z₁-100, z₂=101, Z₂-100, z3-99 .Determine the gear ratio iH1- 2' 2 H Fig. 8-10 Train with two pairs of external gears (双排外啮合周转轮系) 3
Torsian in a Bolid wY Awollow tube The figure above shows a rig which is used to find the angle of twist for a shaft. A torque is applied to the shaft by applying a force to the torque arm, as shov on the right hand side of the figure above. Given Load applied to end of torque arm = 90 N Length of torque moment arm = 150 mm Length of shaft(L) = 300 mm Young's modulus of steel = 205 kN/mm22 Modulus of rigidity 84 kN/mm22 Solid shaft diameter = 15 mm
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth %3D %3! Calculate the output angular velocity at Gear D (WD). Give your answer in rads-1 to the nearest radian. Gear D Gear A Gear D Gear Input Gear A (2500 rpm) Output Gear D
Q1a
3.[填空题] For a pair of standard gears, the module is m=2.5mm, pressure angle is a=20 °. h,*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) %D the diameter of reference circle, d2= Omm the diameter of addendum circle da2 =( Omm the diameter of dedendum circle df2 =( )mm
400 mm Fr= 800 150mm C 600 N -Fa = 400 150mm Ft = Draw bending torsional moments, shear forces and normal force diagrams for the given gear shaft system.