5. In the figure below, gear A is the first driver in the compound gear train. If gear A makes one revolution, how many revolutions will gear B make? 50T 30T 40T 80T 36T 20T B

Q: What is Kinetic energy?

A: Kinetics energy is often studied in physics science and it is described as the kinetic energy of a…

Q: A runner wants to finish a 400 m race in 48.9 seconds. He accelarates from rest and attained his…

A:

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: 1959 lb car starts from rest at point 1 and moves without friction down the track shown. Determine…

A: Mass, m = 1959 lb Radius, r = 20 ft Gravitational-Force, g = 9.81 m/s2  OR 32.2 ft/s2 a = 49 ftb =…

Q: informations of Thermal system

A: Thermal systems are those that include the capacity and exchange of heat. Heat stored in a fabric…

Q: The car engine has a torque of 0.4 kNm at 2000 rpm (rev/min). What is the power (kW) at this time?

A: Given data: torque (T) = 0.4 kNm Speed (N) = 2000 rpm Need to determine the power.

Q: Which of the following terms describes the temperature difference in F o that must exist across…

A: The question is asking for the term that describes the temperature difference in Fahrenheit that is…

Q: (c) Consider a person whose exposed surface area is 1.5 m², emissivity is 0.5, and surface…

A: Given Data: A=1.5 m2 Emissivity (e)=0.5 TB=28° C= 301 K Room temperature  two cases a)280 K &…

Q: Explain volumetric efficiency and cite any three factors that affect it

A: The volumetric efficiency and three factor affecting is given.

Q: An air-cooled window DX unit is used for space cooling. The unit has a capacity of 4.5 tons and has…

A: Given Data (with subscripts):The capacity of the air-cooled window DX unit (cooling load): Q_in =…

Q: If block A is intended to move vertically at a constant rate of 2.36m/s, determine the rate (m/s) at…

A:

Q: Two blocks A and B of the same mass 0.86 kg are released from rest on a 29.5° incline when they are…

A:

Q: What is the difference between SATs and FATs?

A: The objective of the Factory Acceptance Test (FAT) is to confirm that the framework is set up…

Q: can you show more steps? i am lost with this explanation. like how did you get accelerations? what…

A:

Q: *107. ssm Two blocks are connected by a wire that has a mass per unit length of 8.50 x 10-ª kg/m.…

A: Let T is the tension, v is the speed of propagation, and u is the mass per unit length of wire…

Q: Radiators are used in most of the houses’ heating. If we happen to place a sofa just in front of our…

A: It’s safe to put furniture in front of a radiator as long as there is at least a foot in-between…

Q: A gas whose force of attraction between its molecules is negligible is called a gas Natural gas None…

A:

Q: What does third kepler's law states?

A: Kepler has given three laws governing the planetary motion. The first law is known as the law of…

Q: The average fuel efficiency for passenger vehicles in the U.S. is 22 mpg. When one gallon of…

A: Given data the average fuel efficiency = 22 miles/gallon carbon (CO2) emission for one gallon=19.6…

Q: Which of the following terms describes the temperature difference in Fo that must exist across the…

A: The answer is provided below.

Q: Why Blade Numbers are essential and needed to be considered in establishing the design of a wind…

A: Blade Number in wind turbine: Blade number refers to the count of blades attached to the rotor hub…

Q: Briefly explain REST. Give one practical example of how it is used in real-life

A:

Q: True or false thermal energy moves from a colder region of an object to a hotter region

A: we are to determine the direction of heat flow

Q: A 1959 lb car starts from rest at point 1 and moves without friction down the track shown. Determine…

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: The end of the cable at A is pulled down with a speed of VA = 7.4 m/s. A VA

A:

Q: Compare the kinetic energy loss rate to the solar radiation loss rate.

A: Here is the solution of your question:-Explanation:To compare the kinetic energy loss rate to the…

Q: If 700 J of work are done in 7 seconds then which of the following is the average power produced?…

A: following is the answer to the above question-

Q: Zeroth law of thermodynamics Deals with heat engines Deals with conversion of mass and energy States…

A:

Q: Lubrication is a method to reduce close contact between surfaces and helps in heat transfer.

A: A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which…

Q: One end of a solid cylindrical copper rod 0.2500 m long and 0.0350 m in radius is inserted inta a…

A:

Q: System for shorter flight times With his invention, Håkan Lans has made it possible to shorten…

A: System for shorter flight times with his invention, Hakan Lans has made it possible to shorten…

Q: diagnostic criteria in Cyclic Voltammetry for an irreversible process

A:

Q: What is the effect of acceleration on a beam of light shone horizontally at one wall?

A: Since the accelerated elevator moves up during the time light travels across the elevator, the…

Q: Describe each of the three methods of heat transfer, in your own words. Make sure to explain how you…

A: As per given  We have to describe  a. Conductionb. Convectionc. Radiation

Q: Task 3 A 3 m tank contains air at 15 C and 400 kPa is connected through a valve to another tank…

A: the volume of second tank is determined from the ideal gas equation of state ,…

Q: Do the sketch for an escalator system is designed to be turned ON if a person to enter is detected 1…

A: Given Escalator To find Design a control unit for energy savings

Q: Give the Comparisons and Contrast of the FF. Media Literacy vs. Information Literacy Media…

A: Media, information, and technology literacy can assist society with catching or stay educated and…

Q: If the material has a low toughness; it can be assessed by in stress-strain diagram. Select one: a.…

A: Make a stress-strain diagram as shown below.