3. The pruning mechanism of a pole saw is shown as it cuts a branch S. For the particular position drawn, the actuating cord is parallel to the pole and carries a tension of 30 lb. Determine the shearing force P applied to the branch by the cutter, the total force supported by the pin at E and the force exerted by member CD. The force exerted by the light return spring at C is small and may be neglected. F 20 X20% Ans. P = 30 lb 200 RE = D B CD = TE L75°

3. The pruning mechanism of a pole saw is shown as it cuts a branch S. For the particular position drawn, the actuating cord is parallel to the pole and carries a tension of 30 lb. Determine the shearing force P applied to the branch by the cutter, the total force supported by the pin at E and the force exerted by member CD. The force exerted by the light return spring at C is small and may be neglected. F 20 X20% Ans. P = 30 lb 200 RE = D B CD = TE L75°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

21. A Single rivet lop joint is to commect 12 mm thick plates by providing 20mm dia. rivet at somm pitch. determine the strength of the joint and joint efficiency. Take working stress in shear in rivets = 80 N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates. = 150 N/mm².
9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45° Probs. 9-6/7 80 MPa
PLEASE PROVIDE COMPLETE SOLUTION THANKS
How do I solve this using Mohr’s Circle
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 135 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). P (1) O 12.85 in. O 14.78 in. O 7.72 in. O 9.47 in. O 11.75 in. 0.5 in.-k 6 in.
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
Station Rainfall (mm) Annual (mm) ДХ (m) ΔΥ (m) Area (m²) A 42 500 10 25 1500 30 480 15 30 2000 50 558 24 30 830 526 500 E 35 590 40 19 1200 Using a rainfall of 386 mm for rain gauge Station D, determine the average depth of rainfall that fell for the watershed using the arithmetic average, and Thiessen polygon method. The areas for the Thiessen polygon method are given in the table above for each station. B.
Please answer the question in the picture, and make sure you do the right work.
Problem 04.107 - Maximum load carrying capacity of a milled rod with known allowable stress A milling operation was used to remove a portion of a solid bar of square cross section. Knowing that a = 30 mm, d = 20 mm, and all = 54 MPa, determine the magnitude P of the largest force that can be safely applied at the centers of the ends of the bar. The magnitude P of the largest force that can be safely applied at the centers of the of the bar is KN.