The clamp shown in (Figure 1) has a rated load capacity of P = 2700 lb. The screw is pin connected at its end B and passes through the pin-connected (swivel) block at A. Figure -3 in. 4 in. 3 in. B 1 of 1 3.5 in. 2.5 in. Determine the compressive force created along segment AB of the screw. Express your answer in kilopounds to three significant figures. FAB = Submit Part B Fc = Submit 15. ΑΣΦ Determine the magnitude of force exerted at pin C. Express your answer in kilopounds to three significant figures. Request Answer Provido Foodbook 195| ΑΣΦ ↓↑ vec ↓↑ Request Answer vec ? kip kip

Q: The beam is constructed using 2 boards and 3 rows of nails spaced equally. A shear force is applied…

A: The moment of inertia

Q: A wide flange A60 steel column has a length of 5.8meters and pinned ends. If Sx=857x103 mm3,…

A: The following are the given information. A=7243 mm2 Fy=414 MPa Sx=857×103 mm3 Sy=135×103 mm3 d=358…

Q: The bolt in the figure below is 1 in. in diameter. If the load P is 10 kips, determine the average…

A: Given-Bolt diameter= 1 inchLoad, P=10kips

Q: strain in the tension bars equal to  0.004 and  in the design process use 60% of this rho max.…

A: Given : DL = 10 kN/m LL = 8 kN/m UDL & 15 kN/m UVL 8 m length fc = 21 MPa and fy = 276 MPa

Q: SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25…

A:

Q: A solid stainless steel [G= 12,500 ksi] shaft that is 30 in. long will be subjected to a pure torque…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Calculate the value of P using both shear stress criteria and angle of twist criteria. The criteria…

Q: 1. The lower ends of the three bars in the figure are at the same level before the uniform rigid…

A: Step 1: Step 2: Step 3: Step 4:

Q: For the steel truss and loading shown, determine the deformation (in inches) of member BD, knowing…

A: First calculate the member force in BD using the method of sections. Then using the HOOKES  formula…

Q: Problem 1: A round solid shaft is subjected to torsion as shown. Find: 1- Maximum torsional shear…

A: T1 = 50 k ft T2 = 20 k ft Gs = 30 x 106 psi Gal = 15 x 105 psi

Q: The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to…

A:

Q: Determine the compressive force (in Ib) in the bars shown after a temperature rise of 164°F if d =…

A:

Q: 4. A block of wood 0.6m x 0.6m x “h" meters in dimension was thrown into the water, if floats with…

A:

Q: There is a journal bearing at A and a thrust bearing at B. The allowable bending stress is oallow =…

A: Given: The allowable bending stress is 14 ksi. Consider the free body diagram.

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.