3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly material with the stress-strain behavior as shown. If a force of P= 110 kip is applied to the bar, determine the stress in the segments AC and AB. o (ksi) 20 |C B 2 ft 3 ft e (in./in.) 0.001

3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly material with the stress-strain behavior as shown. If a force of P= 110 kip is applied to the bar, determine the stress in the segments AC and AB. o (ksi) 20 |C B 2 ft 3 ft e (in./in.) 0.001

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bronze bar 7 m long with a cross sectional area of 498 mm² is placed between two rigid walls as…

A: Given Bronze Bar length, L = 7m Area = 498mm2 Temp = 20° C gap is 3.6mm to determine temperature at…

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see…

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2,…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

Q: Current Attempt in Progress When an axial load is applied to the ends of the bar shown in the…

A: Express the given information in the form of equations. Then using definition of strain the value of…

Q: 60MM PL 30 мм 30 мм комм 40 MM то

A: Hello dear Please find the attached solution below, thanks

Q: 1. A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB. 1.6m…

A: Given data, Area = 300 mm² To find out the stress at AB.

Q: 2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10³…

A: Given data EAB = 2 × 105 N/mm2 EBC = 7 × 104 N/mm2 LAB = 3m = 3000 mm LBC = 2m = 2000 mm A =…

Q: A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position…

Q: 1. A steel bar is subjected to the loads shown in the figure. Determine the total deformation in the…

A: When the material like steel bar or another object is under tension or compression the change in…

Q: A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 3000 N. If the…

A: Solution: Given Data: T1=20°CT2=-20°CP=3000 NAllowable Stress=150 Mpaα=11.7×10-6/°C As per the first…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: To determine the stress in each section of the rod. Given, Load P = 3000 N Area of bronze, Ab =…

Q: ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A…

A: Given data in question Stress 17 & 10 Mpa Shear stress 26 Mpa To find out Principal stresses

Q: The section of a thick beam has the dimensions shown in the figure below. Calculate the section…

Q: 2. The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Given:- Compound bar containing steel, bronze, and aluminum segments is given Properties of the…

Q: In an elastic body without any body force, the Airy's stress function determined as: $ = x*y + 4x²y3…

A: Introduction- The biharmonic equation in mathematics is a 4th partial differential equations that…

Q: A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

100%

3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly
material with the stress-strain behavior as shown. If a force of P= 110 kip is applied
to the bar, determine the stress in the segments AC and AB.
o (ksi)
P
20
|C
B
-2 ft
- 3 ft
e (in./in.)
0,001

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two- dimensional stress, , = 310 N/mm² (tensile) and , -300 N/mm² (compressive). E = 2 × 10 N/mm², Poisson's ratio=0.3. The elongation of the bar is the direction of , will be
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see figure). The wire is made of high-strengthsteel having a modulus of elasticity E = 210 GPa andyield stress σY =820 MPa. The length of the wire isL =1.0 m, and its diameter is d =3 mm. The stress straindiagram for the steel is defined by the modifiedpower law, as σ =Eε 0<σ≤σy σ = σy[Eε/σy] σ≥σy (a) Assuming n = 0.2, calculate the displacementδB at the end of the bar due to the load P. Takevalues of P from 2.4 kN to 5.6 kN in incrementsof 0.8 kN.(b) Plot a load-displacement diagram showing Pversus δB.
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
Part 2,3,4
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
i need part 2 of this question
X Your answer is incorrect. A small aluminum alloy [E = 75 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b = 21 mm, d= 32 mm, and t = 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 7 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d D E 2 H b Answer: P = i 112.79 N %3D
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa