3. OF (AZIM 210°); OG (AZIMN 325° 55'); OH (AZIM 115° 10') Angles FOG and FOH and GOH

Q: Determine the true length of lines SD and PF. Then draw the point view of line SD. Use only two…

A:

Q: Determine the location of the neutral axis from the top of the beam. 24" 15" 22" 1 #11

A: Determine the location of the neutral axis from the top of the beam.

Q: We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is…

A:

Q: Determine the height h above the base of the 13.57" T 1.24" 1.24" £ 6.33" -0.86" 12.05"

A:

Q: A straight line AB 100 mm long is inclined at 45° to VP. End B of the line is 30 mm aboveHP and HT…

A: Length of line AB = 100 mm AB is inclined at 45o to VP. End B of the line is 30 mm above HP…

Q: Could you also help me to determine the bending moment at D?

A: This question is related to the Strength of the material from Civil Engineering. This is attached…

Q: Hinge TT Determine the degree of indeterminacy (i) of the frame shown.

A:

Q: Basic 1. General Use the POLYGON command to draw the hexagon as shown. Fully constrain the hexagon…

A: Given Sample drawing To draw Drawing similar to given drawing with different dimension and the steps…

Q: The cross section at station 2+60 has a cut area of 9 ft2 and a fill area of 4 ft2 and the cross…

A: Cut Area of the cross-section at station 2+60,A2+60=9ft²Cut Area of the cross-section at station…

Q: Given a true bearing of a line from X to Y as N 4° W where the magnetic declination is 16° W.…

A: Given:-  Given a true bearing of a line from X to Y as N 4° W where the magnetic declination is 16⁰…

Q: Guide: W = 447 Z = 587 Y = 176 X = 388 "W" "Y" "Y" "X" all dimensions are in mm "Y" a. Determine the…

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: 200KN TookN 5m 10m 2I E> CONSTANT =250 GPa I> GO0(10°) mm4 %3D

A:

Q: The window is held open by chain AB. Determine the length of the chain, and express the 50-lb force…

A:

Q: 10 kN B, 600 mm² 25 kN 600 mm2 1.2 m 1200 mm? 1200 mm2 D -0.9 m Both ends are connected with pins.…

A:

Q: I need help figuring out how to do this when P is at an angle

A: Given: The weight of the block is 100 lb. The coefficient of static friction is 0.25. Consider the…

Q: d] Draw the deflected shape of the beam below

A:

Q: The bar shown below is inclined at 45 degrees with the horizontal and at equilibrium. The force at C…

A: Given data  Member inclined at 45° with horizontal Find reaction at E.

Q: y Problem 3 10mm Determine: a. Determine the location of the centroid of the figure, x and y.…

A: Let the given figure is divided into two sections i.e Section 1 and Section 2. Let (x1,y1) and (x2,…

Q: 4- Determine the vertical and horizontal deflections at joint B of the truss shown using the virtual…

A: Vertical Load = 100 kN Horizontal load = 50 kNArea = 1000 mm2E = 70 GPa or 70000 MPa

Q: Problem 7: Determine the angle 0 between the y axis of the pole and the wire AB. 3 ft 2 ft 2 ft 2 ft

A: Given :- To find :- Angle between y axis of the pole and wire AB

Q: Determine the height above the base of the centroid of the cross-sectional area of the beam. Neglect…

A:

Q: Draw the B.M.D for the following

A: The diagram given in the question is as follows:

Q: | EI, EA=const

A:

Q: Correctio Interior Forward Back Line Length(m) Forward Back d internal n Sta angle bearing bearing…

A: Solution: The calculation as per the figure of traverse:

Q: Determine degree of static indeterminacy Hinge A B C D

A: Given data : Number of member (m)=4Number of external support reaction (R)=2+1+1+1=5Number of…

Q: Construct the third projection of the prism and complete the other two projections of point A, B, C…

A: Given prism and asked to draw third projection of prism.

Q: Q4/ For the figure 2: 1-value of the contour interval. 2- value of x. 3- draw the .profile of…

A: There are 4 contour lines and 5 contour intervals between contour line 50 and contour line 75. That…

Q: Determine degree of static indeterminacy

A: Given data : Number of external support reaction (R)=1+2=3 Number of member (m)=6 Number of joint…

Q: Determine degree of static indeterminacy of truss

A: Given data : Number of member (m)=13 Number of Joint (J)=8 Support=Pinned and roller support Number…

Q: Determine the force acting on the curved part. Indicate your location

A:

Q: 3.) At the interior hinge 10 9. 6.

A:

Q: Compute the maximum El5 of the beam shown below. wit

A: Step 1

Q: Point B is an internal hinge. Find Ay, MA, and Cy. 30 kN 60 kN/m 25 kN 20 kN В 2 m 3 m 2 m 1.5 m 1 m

A:

Q: Draw the plan and elevation of rectangular plate PQRS(PQ=30mm , QR= 35mm) when it's corner Q is 2cm…

A: - The representation of rectangular plate is shown in figure below.

Q: Determine the degree of indeterminacy of the structure below 02

A:

Q: A 180 kN 1.5 m 1.5 m 3 m Hinge B 3 m 180 kN 3 m

A:

Q: 1. A square prism with 40 mm edges and an axis of 55 mm rests on its base with its side faces…

A: The objective of the question is to draw the front view, top view in section and auxiliary view of a…